manualshive.com logo in svg

MS Sedco INTERSECTOR, Installation Instructions Manual, Page: 7 / 53

Share
Download
MS Sedco INTERSECTOR Installation Instructions Manual Download Page 7

INSTALLATION

INSTALLATION PREPARATION

 

NOTE:  Remember to read all installation instructions carefully prior to 

 

installation of the unit.  For a quicker installation, carefully pre-screen installation 

 

location.  Prior to installation of the INTERSECTOR, please complete the 

 

INTERSECTOR worksheet.  The worksheet is included with this manual.

Please inspect mounting location to ensure the following criteria are met:

•  Mounting height should be between 14 feet and 20 feet. 
•  Distance from the sensor to the stop bar should not exceed 140 feet. 
•  Distance from the sensor to the closest detection zone should be at least 50 feet. 
•  Typical range of the TC-CK1-SBE is 600 feet.
•  The TC-CK1-SBE has a detection width of 30 degrees. For best results the sensor 
  should be mounted at a tilt angle between horizontal to 3 degrees downward plus or 
  minus the road slope. 
•  Installation requires a laptop with Internet Explorer version 6.0 or greater, at least 
  2 GB RAM available, safe cable & Ethernet cable.
TOOL REQUIREMENTS:
To properly install the INTERSECTOR, it is necessary to have the following tools on 
hand:
 

•  Angle Meter 

•  Ethernet Cable Tester

 

•  7/16” Box Wrench or Socket 

•   Modular Plug Termination Tool 

 

 

 

 

(Crimp Tool)

The INTERSECTOR is designed to be mounted at a height of 14 to 20 feet on a corner 
signal pole or on a mast arm no further than 10 feet from the signal pole.  Maximum 
offset angle from traffic direction should be ±15 degrees.  Mounting outside this range 
may reduce performance.  Mount the sensor to the pole using stainless steel banding or 
bolts (not included).  Make sure the sensor is mounted level.  

INTERSECTOR ANGLE SETTINGS:
There are two angle settings for the INTERSECTOR; side to side (azimuth) and up and 
down (elevation). The azimuth setting is accomplished visually using the gun sight at 
the top of the unit.  Aim the gun sight across the center of the stop bar region.  Check to 
ensure that cars should be tracked approximately 30 feet past the stop bar for a left turn 
lane.  To set the elevation, use the angle meter which is included in the INTERSECTOR 
installation kit.  The Installation Table Recommended Settings below provides initial 
settings for installation, based on the distance to the stop bar.  These settings may need 
additional adjustment depending on factors such as the slope of the road.  Rotating the 
unit downward will decrease total range, but will ensure detection closer to the unit. 

INTER

SECTOR 

Microwave Motion and 

Presence Sensor Installation Instructions

MS Sedco INTERSECTOR Installation Instructions 

Page 7 

INTERSECTOR-1.9Uv092717

!

Summary of Contents for INTERSECTOR






















































Reviews:

No comments