manualshive.com logo in svg

MS Sedco INTERSECTOR, Installation Instructions Manual, Page: 27 / 53

Share
Download
MS Sedco INTERSECTOR Installation Instructions Manual Download Page 27

CHANGING THE INTERSECTOR IP ADDRESS (cont.)

•  Confirm you can access this address by opening the webpage using the new IP 

address. 

To confirm or set the IP address on the TCIB, connect the laptop to the TCIB via RS232. 
Connect the laptop to the laptop port of the TCIB via Ethernet cable. Connect the 
INTERSECTOR Ethernet cable to the Setup port of the TCIB. You can also connect to the 
INTERSECTOR and TCIB via Ethernet switch or hub. The INTERSECTOR should be 
connected to the TCIB Setup port via Ethernet cable, and the TCIB Operational port 
should be connected to the Ethernet switch or Hub. 

 

WARNING: 

 

Ensure that the TCIB “Operational” port is connected to the Ethernet 

 

switch or hub with the cable labeled “Ethernet Switch Safe” or that the cable has 

 

been modified to disable voltage lines. 

 

WARNING:  If you are setting up an Ethernet switch or multi-port hub to access 

 

the INTERSECTOR it is important to use a modified Ethernet cable between the 

 

“Operational” port of the TCIB and the switch or hub. This cable should be 

 

modified to ensure voltage is not transmitted to the switch or hub.  Ethernet 

 

Switch Safe cable is available from MS Sedco.  To construct one of the cables it 

 

is necessary to disable pins 4, 5, 7, and 8.  

Open the default webpage (192.168.0.100) and note you are challenged with a password. 
Run “IP_Address_Set.exe”. On the INTERSECTOR tab under the Connection Select 
mark “Internet” since you are connecting via Ethernet cable. Ensure that the correct 
INTERSECTOR IP Address is shown in the box next to the “Connect Internet” button. 
Click on the “Connect Internet” button. A message will be displayed to show you are 
now connected to the INTERSECTOR.

INTER

SECTOR 

Microwave Motion and 

Presence Sensor Installation Instructions

MS Sedco INTERSECTOR Installation Instructions 

Page 27 

INTERSECTOR-1.9Uv092717

Ethernet 
Switch 

INTERSECTOR

 

HOST

TCIB card  

 

Laptop 

Ethernet 
cables 

Laptop 

Set-up

 

Operational 

!

!

Summary of Contents for INTERSECTOR






















































Reviews:

No comments