manualshive.com logo in svg

MS Sedco INTERSECTOR, Installation Instructions Manual, Page: 45 / 53

Share
Download
MS Sedco INTERSECTOR Installation Instructions Manual Download Page 45

INTER

SECTOR 

Microwave Motion and 

Presence Sensor Installation Instructions

MS Sedco INTERSECTOR Installation Instructions 

Page Addendum-5 

INTERSECTOR-1.9Uv092717

EXPLANATION OF CHANGES (CONTINUED)

Save and Load Zone Data

The Save and Load Zone Data feature allows the user the ability to store and retrieve 
INTERSECTOR setup and Zone setting data. When the Save Zone Data button is 
selected, a text file containing the current values from the Setup and Zone Settings 
pages will be downloaded to the computer. Selecting Load Zone Data will allow the user 
to navigate to a location that contains previous save files, using the browser window 
that appears. Selecting a file and clicking OK will load the saved values into the Setup 
and Zone Settings pages. 

 

NOTE: Internet Explorer and Microsoft Edge will occasionally fail during upload. 

 

Google Chrome and Mozilla Firefox are recommended web browsers for using the

 

Load Zone Data feature.

The interface to Save Zone Data files will depend upon the web browser being used, and 
which settings are selected. The following sections provide details for using the Save 
and Load Zone Data feature with the four web browsers previously mentioned.

!

Figure 7

Summary of Contents for INTERSECTOR






















































Reviews:

No comments