mru OPTIMA7 biogas User Manual Download Page 75

Page: 75 / 78

USER MANUAL OPTIMA 7 Biogas

MRU GmbH, D-74172 Neckarsulm

75 / 78

11.6.

Troubleshooting

Troubleshooting the analyser

1. Effect

2. Error indication

3. Cause

4. Solution

Device cannot be
switched off by
pressing the OFF
key.

LED behind the con-
densate separator is
on and the LCD dis-
play is dark

Device does not re-
act on any key.

Press ESC and ON sim-
ultaneously!
EMERGENCY OFF
After this, the date and
time have to set new.

Inside of the device
is too cold, device
not ready for oper-
ation.

Display indication:

“Device too cold” or

audible sound every
5 sec.

e.g. device was stored
in a cold place during
winter.

Put the device to a
warm room and wait

Measuring values
are not correct

Sensors already get in
trough with the gas
during calibration.

Vent device with fresh
air and re-start!

No measurement
possible

Device cannot be
switched on or does
not react after being
switched on.
Battery discharge

Connect the device to
the line power in order
to charge the battery.

Measurement with-
out exact tempera-
ture values.

Temperature indica-
tion:
- - - , - °C

Thermo element de-
fective, balancing net-
work interrupted or
not connected.

Call our after-sales
service.
Remove probe from
the gas duct and con-
densate from the
probe tube.

Wrong measuring
values

Measuring range ex-
ceeded:
Value O

too high

Values CO and CO

to low

Connection probe

–

device not correct.
Leakage at probe /
tube / condensate
separator, pump does
not suck correctly

Effect tightness test!
By visual control of
probes, tubes conden-
sate separator, leaking
parts could be found.

Wrong measuring
values

Gas temperature is
too hot or alternates

Probe is not plugged
in correctly, defective
cable in the probe line,
formation of conden-
sate at the probe tip.

Check probe plug re-
spectively probe line
regarding damages
(loose connection), re-
move condensate
from the probe tip.

Summary of Contents for OPTIMA7 biogas















































































Search results

Summary of Contents for OPTIMA7 biogas

Reviews:

Related manuals for OPTIMA7 biogas

Brands by name

Popular brands

mru OPTIMA7 biogas, User Manual

Search results

Summary of Contents for OPTIMA7 biogas

Reviews:

Related manuals for OPTIMA7 biogas

Brands by name

Popular brands