mru OPTIMA7 biogas User Manual Download Page 38 | Manualshive

Page: 38 / 78

background image

USER MANUAL OPTIMA7 Biogas

MRU GmbH, D-74172 Neckarsulm

38 / 78

7.9.

Pressure measurement (option)

Pressure (4 values) is measured and saved to the selected measurement
name. The actual measured value is displayed in the middle of the dis-
play. The 4 measurement names can be changed as desired.
The hose on the draft + connector must be connected for draft meas-
urements.
The second hose on the Delta P- connector must be connected for dif-
ferential measurement

.

►

Go to the Measurement menu.

►

Select Pressure measurement.

►

Press OK.



The Menu Pressure measurement appears.

►

If necessary, press the Menu Key to change the name.



A selection list appears.

►

Select Modify name.



A window appears.

►

Adapt the name to your needs.

►

Press OK.



The changed name appears in menu Pressure measurement.

►

If necessary, press F1 to accept the current value.

►

If necessary, press F2 to take a zero point.

►

If necessary, press F3 to save the measured values

«
...
36
37
38
39
40
...
»

Summary of Contents for OPTIMA7 biogas















































































Reviews:

No comments

Related manuals for OPTIMA7 biogas

Brand: Narvitech Pages: 2

Brand: Waterproof Pages: 10

Brand: Ocean Optics Pages: 43

Brand: Ocean Technology Systems Pages: 12

Brand: Ocean Reef Pages: 24

Brand: Wagner Meters Pages: 17

YPP-100 Light Piano

Brand: Yamaha Pages: 54

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 56

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 32

Brand: LEGRAND Pages: 5

Digital Piano CA750

Brand: Kawai Pages: 76

Brand: Kawai Pages: 110

Brand: Hanna Instruments Pages: 2

Brand: Vogel Pages: 4

K-PATENTS PR-23 AX Series

Brand: Vaisala Pages: 246

Brand: Megasat Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands