mru OPTIMA7 biogas User Manual Download Page 21

Page: 21 / 78

USER MANUAL OPTIMA 7 Biogas

MRU GmbH, D-74172 Neckarsulm

21 / 78

First usage

After the analyser has been inspected and is ready for start-up it can be
switched on and personalized settings can be entered. These settings can
be changed at any time.

5.1.

Preparatory steps

►

Unpack the analyser.

►

Read the User Manual completely.

►

The analyser leaves the factory assembled and ready for use.
Nevertheless, check the device for completeness and integrity.

►

Charge the battery of the analyser for about 8 hours.

►

Check date and time. Modify if needed.

5.2.

Analyzer settings

LCD brightness

–

100 %

Display-brightness, depending on tempera-
ture and also on the personal judgement of
the user, at 20°C a value of ca. 50% is normal

Language

Option

Select device languages

Country

option

Enables some country specific parameters like
fuel types, calculated values etc.

Site administration ON / OFF

The sites administration can be switched off.
Therefore, only one site is active.
Each measurement will be stored on site 1!

Attention!

All measurements will be deleted by switching
the site administration ON/OFF!

LED condensate
separator

0 … 150

Change the brightness of the condensate
separator LED

Helping hints

ON / OFF

Helpful hints activated or deactivated (expla-
nation below)

Switch-ON protec-
tion

ON / OFF

If activated and if ON key is pressed (possibly

inadvertently), then the message „3 seconds

OK key press is displayed

Keyboard beeper

ON / OFF

Keyboard beeper activated or deactivated

Logo switch ON

ON / OFF

Logo will be displayed

Summary of Contents for OPTIMA7 biogas















































































Search results

Summary of Contents for OPTIMA7 biogas

Reviews:

Related manuals for OPTIMA7 biogas

Brands by name

Popular brands

mru OPTIMA7 biogas, User Manual

Search results

Summary of Contents for OPTIMA7 biogas

Reviews:

Related manuals for OPTIMA7 biogas

Brands by name

Popular brands