mru OPTIMA7 biogas User Manual Download Page 41

Page: 41 / 78

USER MANUAL OPTIMA 7 Biogas

MRU GmbH, D-74172 Neckarsulm

41 / 78

Gas composition

Gas composition manual
standard

Air, Gas, Biogas

O2 [%]

max. 100 %

CO2 [%]
CH4 [%]
H2O [%]
N2 [%]
Molar mass
[g/mol]

depending on gas composition

Pitot factor

Enter the value „Pitot factor“.

Please take the value from the documentation of the used Pitot tube.

Damping (T90/s)

With this parameter you can set the averaging time of the pressure sen-
sor. The unit is the time in seconds needed for a 90% change.

Calculation

Molar mass

The molar mass of a gas depends on the gas proportions.
This will be calculated on the equation 1

Equation 1: molar mass

M =

0.00001* (32*[O

] + 44*[CO

] + 18*[H

O] + 16*[CH

] + 28*[N

])

[O2]: oxygen in [%]
[CO2]: carbon dioxide in [%]
[CH4]: methane in [%]
[H2O]: water in [%]
[N2]: nitrogen in [%]

Unit of molar

mass:

Summary of Contents for OPTIMA7 biogas















































































Search results

Summary of Contents for OPTIMA7 biogas

Reviews:

Related manuals for OPTIMA7 biogas

Brands by name

Popular brands

mru OPTIMA7 biogas, User Manual

Search results

Summary of Contents for OPTIMA7 biogas

Reviews:

Related manuals for OPTIMA7 biogas

Brands by name

Popular brands