MR VACUTAP VM I 1002 Operating Instructions Manual Download Page 12

Page: 12 / 82

2 Safety

Maschinenfabrik Reinhausen GmbH 2020

4360571/02 EN

VACUTAP

Work area

Untidy and poorly lit work areas can lead to accidents.

▪ Keep the work area clean and tidy.

▪ Make sure that the work area is well lit.

▪ Observe the applicable laws for accident prevention in the relevant coun-

try.

Working during operation

The product may only be operated in a sound, operational condition. Other-
wise it poses a danger to life and limb.

▪ Regularly check the operational reliability of safety equipment.

▪ Comply with the inspection work, maintenance work and maintenance in-

tervals described in this technical file.

Explosion protection

Highly flammable or explosive gases, vapors and dusts can cause serious
explosions and fire. This increases the danger to life and limb.

▪ Do not install, operate or perform maintenance work on the product in ar-

eas where a risk of explosion is present.

Safety markings

Warning signs and safety information plates are safety markings on the
product. They are an important aspect of the safety concept.

▪ Observe all safety markings on the product.

▪ Make sure all safety markings on the product remain intact and legible.

▪ Replace safety markings that are damaged or missing.

Ambient conditions

To ensure reliable and safe operation, the product must only be operated
under the ambient conditions specified in the technical data.

▪ Observe the specified operating conditions and requirements for the in-

stallation location.

Auxiliary materials and operating materials

Auxiliary materials and operating materials not approved by the manufac-
turer can lead to personal injury, damage to property and malfunctions of the
product.

▪ Use insulating fluids that meet the requirements in accordance with IEC

60296.

▪ If approved by the transformer manufacturer, you can use alternative insu-

lating fluids approved by Maschinenfabrik Reinhausen GmbH.

Summary of Contents for VACUTAP VM I 1002



















































































Search results

Summary of Contents for VACUTAP VM I 1002

Reviews:

MR VACUTAP VM I 1002, Operating Instructions Manual, Page: 12 / 82

Search results

Summary of Contents for VACUTAP VM I 1002

Reviews: