background image

mr

.

steam

®

         

Steam@Home

®

 

Installation, Operation & Maintenance Manual

________________________________________________________________________

IN

S

T

A

L

L

E

R

 

5

Provide unions to facilitate installation 
and disconnect of piping

Steam       

Generator

Field  installed  
power supply

Field installed 1/2” insulated 

steam supply pipe

Drain Valve should be closed

See Page 13 for draining information 

Control cable

(located behind  the wall)

Steam Head (shown with acrylic shield)
See page 7  for Steam Head Installation 
information

Field installed  

water supply line

SteamStart

®

 Control

See page 12
for installation 
information.

tyPICAL Mr.StEAM INStALLAtIoN

 

To avoid unintentional steambath operation, do not locate the control 

where other controls, shower heads, valves, body sprays or similar accessories within the shower 
could cause confusion or interfere with the MrSteam control’s intended use and function.

 

Consult with supplier of acrylic, fiberglass and other 

non-heat resistant enclosures for recommended steamhead location. Use 
Acrylic Shield PN MS-103938. See instructions provided with steam shield.

NOTE: 

For illustrative purposes only. Consult 

with qualified designer, architect or contractor 
for steam room construction details.

IMPORTANT NOTE: 

Install cable in a 

dedicated conduit to allow for replacement. 
Be careful not to strain, staple, pinch or 
otherwise damage the control cable. Do not 
route in conduit with power wires.

IMPORTANT NOTE

:

 

Provide a minimum of (12) inches at 

plumbing end and top of the steam generator or as required 
for servicing. Alternately, provide unions as required to facilitate 
installation and disconnection of the steam generator.

IMPORTANT NOTE: 

The minimum clearance from com-

bustible surfaces is zero all around.

5

5

8

(138)

7

3

4

(197)

1

1

4

(32)

12”

(305)

14

7

8

(378)

1

7

8

(48)

3

3

8

(86)

5

3

16

(132)

2

1

2

(64)

14

3

8

(365)

1

1

2

”(38)

Water Inlet

SteamStart

®

Connection

Steam Outlet

Manual 

Drain 
Valve

Safety Valve

T

o AVoID EQUIPMENt DAMAGE Do Not CoNNECt 

POWER SUPPLY DIRECTLY TO ELEMENT TERMINALS !!!

NOTE:  

For ILLUStrAtIVE PUrPoSES oNLy. 

!

C A U T I O N

!

C A U T I O N

Summary of Contents for Steam@Home 3000

















Reviews: