background image

mr

.

steam

®

         

Steam@Home

®

 

Installation, Operation & Maintenance Manual

________________________________________________________________________

IN

S

T

A

L

L

E

R

 

STEAMSTART

®

 

On/Off Switch

Box Contents: 

 

•฀SteamStart฀Control

 

•฀Control฀Cable

INSTALLING THE STEAMSTART

®

 CONTROL

The SteamStart has a 30 foot cable with a Plug & Play  
connector at both ends. (Diagram 1).  
A 60 foot control cable is available (103978-60). 
Contact a MrSteam technical representative if the 60 foot  
cable is required.

 

To avoid unintentional steambath operation, 

do not locate the control where other controls, shower heads, 
valves, body sprays or similar accessories within the shower 
could cause confusion or interfere with the MrSteam control’s 
intended use and function.

StEP 1 

Diagram 2

Drill a 7/8 inch diameter hole in a preferred wall location.  
Do not oversize or undersize the hole.

StEP 2 

Diagram 3

Route the cable from the wall to the steam generator.  
Be careful not to strain, pinch or otherwise damage the  
control cable.

StEP 3 - 

Diagram 4

Remove and discard the peel-off paper from the switch  
housing to expose the adhesive as shown in Diagram 4.

StEP 4

 - 

Diagram 5

Apply silicone (provided with SteamStart control) to the  
hole in the wall as required to create a moisture seal.  
Apply silicone to the back of the switch as required to seal 
grout lines or as required for additional adhesion.

IMPORTANT NOTE:

 Use care not to apply silicone  

to the adhesive gasket.

STEP 5 

Push cable and switch housing into the hole firmly.  

STEP 6

 - 

Diagram 6

Firmly connect the Plug & Play connector to the steam  
generator connector labeled SteamStart. 

NOTE: 

The connector is keyed and will only connect  

in one orientation with the tab facing up.

IMPORTANT NOTE:

 

Install cable in a dedicated conduit to  

allow for replacement. Be careful not to strain, staple,  
pinch or otherwise damage the control cable.  
Do not route in conduit with power wires.

SWITCH

                            

DIAGrAM 1

DIAGrAM 2

 DIAGRAM 3

                      

DIAGrAM 4

                      

DIAGRAM 5 

   DIAGRAM 6

12

DIMENSIONAL INFORMATION

!

C A U T I O N

PLUG & PLAY

CONNECTOR

30’ CABLE

Summary of Contents for Steam@Home 3000

















Reviews: