DO NOT route iSteam, AirTempo, iTempo/Plus,
iTempo, HomeWizard or iGenie control wiring inside conduit
together with power lines or close to hot water or steam piping.
Doing so may result in an inoperative or hazardous installation.
DO NOT alter or modify any MrSteam product. Doing so may
result in an inoperative or hazardous installation and will void the
UL listing and warranty.
IMPORTANT NOTES:
1. Turn power to the steam generator OFF before connect-
ing the control to the generator. Failure to turn the power
off will result in an inoperable control.
2. DO NOT operate iSteam, AirTempo, iTempo/Plus, iTempo,
HomeWizard or iGenie controls with other than a MrSteam
iSteam, AirTempo, or iTempo compatible steam generator.
MrSteam residential steam generators with serial numbers
lower than 900000, or any other brand of steam generator
are not to be operated with iTempo controls. Doing so
may result in an inoperative or hazardous installation.
If iSteam is used with a generator having serial number
less than 1174000, contact MrSteam technical support for
an upgraded PC board.
3. This document contains important safety, operation and
maintenance information. Leave this document with the
homeowner. Do not discard this document.
4. Discontinue use of the steam generator or control if the
steam generator is damaged or otherwise not functioning
properly. Operating a damaged steam generator may
result in an inoperative or hazardous installation
mr.steam
®
Installation, Operation & Maintenance Manual
_________________________________________________________________________
I
N
S
T
A
L
L
E
R
20
BEFORE INSTALLING
Turn power to the steam generator OFF before connecting the
control to the generator. Failure to turn the power off will result in
an inoperable control.
To avoid unintentional steambath operation,
DO NOT locate the control where other controls, acces-
sories, shower heads, valves, body sprays or similar within
the shower could cause confusion or interfere with the
MrSteam control’s intended use and function.
DO NOT use any iSteam
®
, AirTempo
®
,
iTempo/Plus
®
, iTempo
®
, HomeWizard
®
or iGenie
®
controls
without reading and understanding its own manual and the
MrSteam steam generator Installation and Operation Manual.
Failure to read and understand these instructions may result
in an inoperative or hazardous installation.
A peel and stick warning sticker must be read
and permanently affixed in a conspicuous location near the
steam room. Failure to read and affix this warning sticker in a
conspicuous location may result in serious injury or death. .
Install the iSteam, AirTempo, iTempo or iTempo/Plus controls
according to installation instructions. Failure to install accord-
ing to instructions will result in an inoperative control or haz-
ardous overheating or inadequate heating of the steam room.
If an iSteam, AirTempo, iTempo or iTempo/Plus control is
installed outside the steam room a Remote Temperature
Probe (PN MSTS) must be installed inside the steam room
per installation instructions supplied with the Remote
Temperature Probe. Failure to install according to instructions
will result in an inoperative control and overheating of the
steam room.
CONTROL INSTALLATION
Refer to Control Manual for specific installation requirements
CONTROL ROUGH IN
Refer to Installation Instructions for the specific control
IMPORTANT
NOTE:
The
control
cable
should
be
run
in
a
dedicated
1”
conduit
to
facilitate
installation
and
service.
1.
Determine
the
desired
installation
location
of
the
con-
trol.
The
iSteam
®
,
AirTempo
®
,
iTempo
®
and
iTempo/Plus
®
controls
are
designed
to
be
installed
inside
or
outside
the
steam
room
as
a
matter
of
personal
preference.
If
the
con-
trol
is
installed
inside
the
steam
room
the
control
must
be
located:
2.
4 - 5
feet
above
the
floor
near
the
bather
seating
area
3.
The
control
features
an
integral
temperature
sensor.
Locate
the
control
in
a
location
representative
of
the
desired
steam
bathing
temperatures.
DO
NOT
locate
the
control
above
or
near
the
steam
head
or
direct
steam
emissions.
4. On a vertical wall
The
iSteam
and
iTempo
control
cable
length
is
30
feet.
Insure
that
the
control
and/or
steam
generator
are
locat-
ed
accordingly.
An
optional
60
foot
cable
is
available,
PN
103990-60
for
AirTempo
and
iTempo
and
PN
104117-60
for
iSteam.
Contact
a
MrSteam
technical
service
representative
if
a
60
foot
cable
is
required.
Excess
control
cable
should
be
neatly
coiled
and
twisted
into
a
figure
8.
The
AirTempo
dongle
is
provided
with
a
3
foot
cable.
The
maximum
cable
length
is
60
feet.
IMPORTANT
NOTES:
• If
the
control
is
installed
outside
the
steam
room
a
Remote
Temperature
Probe
Part
Number
MSTS
must
be
installed
inside
the
steam
room,
depending
on
the
control.
• Insure
MrSteam
steam
generator
is
iSteam,
AirTempo
or
iTempo
compatible
and
has
a
serial
number
900000
or
high-
er.
If
iSteam
is
used
with
a
generator
having
serial
number
less
than
1174000,
contact
MrSteam
technical
support
for
an
upgraded
PC
board.
• See
instructions
for
the
MSTS
Temperature
Probe
(located
in
the
Control
Installation
Manual
related
to
your
specific
control
package)
before
rough-in
or
installation
of
control.