mr. steam iTEMPO Installation, Operation & Maintenance Manual Download Page 5

mr

.

steam

®

  

Installation & Operating Instructions

_________________________________________________________________

4

BeFOre iNStaLLiNG

Carefully inspect the control and packaging for shipping 

damage. In the event of shipping damage, please contact 

the carrier for claim information. Our customer service de-

partment can assist you with any missing or damaged parts.

 

To avoid unintentional steambath  

operation, do not locate the control where other controls, 

accessories, shower heads, valves, body sprays or similar 

within the shower could cause confusion or interfere with 

the MrSteam control’s intended use and function.
Do not use any iTempoPlus

®

, iTempo

®

, HomeWizard

®

 or 

iGenie

®

 controls without reading and understanding the 

respective Installation and Operation Manual and MrSteam 

steam generator Installation and Operation Manual. Failure 

to read and  understand these instructions may result in an 

inoperative or hazardous installation.
 

A peel and stick warning sticker is provided 

in the MrSteam steam generator Installation, Operation 

and Maintenance Manual. This manual is provided with 

every steam generator. The warning sticker must be read 

and permanently affixed in a conspicuous location near the 

steam room. Failure to read and affix this warning sticker in 

a conspicuous location may result in serious injury or death. 

Please call MrSteam at 800 767-8326 for a free replacement 

or if you have any questions regarding the warning sticker. 
Install the iTempo or iTempoPlus controls according to 

installation instructions. Failure to install according to in-

structions will result in an inoperative control or hazardous 

overheating or inadequate heating of the steam room. 

Failure to install according to instructions will result in an 

inoperative control and overheating of the steam room.

impOrtaNt NOte: 

If the desired location for the control 

is outside the steam room a Remote Temperature Probe 

(MSTS) must be installed inside the steam room. Contact 

CaUtiON

!

MrSteam technical service 1-800-767- 8326 for 

more information on the Remote Temperature 

Probe.
 

Do not route iTempoPlus, iTempo, 

HomeWizard or iGenie control wiring inside conduit 

together with power lines or close to hot water or 

steam piping. Doing so may result in an inoperative 

or hazardous installation. 
 

Do not alter or modify any MrSteam 

product. Doing so may result in an inoperative or 

hazardous installation and will void the warranty.

impOrtaNt NOteS:

• Turn power to the steam generator OFF before 

connecting the control to the generator. Failure 

to turn the power off will result in an inoperable 

control.

• Do not operate iTempoPlus, iTempo, Home  

Wizard or iGenie controls with anything other 

than a MrSteam iTempo compatible steam gen-

erator. MrSteam residential steam generators 

with serial numbers lower than 900000, or any 

other brand of steam generator are not to be op-

erated with iTempo controls. Doing so may result 

in an inoperative installation.

• This document contains important safety, opera-

tion and maintenance information. Leave this 

document with the homeowner. Do not discard 

this document.

• Discontinue use of the steam generator or control 

if the steam generator is damaged or otherwise 

not functioning properly. Doing so may result in 

an inoperative or hazardous installation.

• All illustrations are for illustrative purposes only.

WarNiNG

!

WarNiNG

!

WarNiNG

!

Summary of Contents for iTEMPO



































Reviews: