manualshive.com logo in svg

MQ Multiquip WHITEMAN Series, Manual

Share
Download
MQ Multiquip WHITEMAN Series Manual Download Page 24

PAGE 24 — STXDF TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #0 (11/05/18) 

INSPECTION

FLUID LEVELS

Record the following fluid levels on Machine Information and 

Maintenance Log in Inspection section. Refer to Fluid Fill and 

Check section for procedure.

 

„

Engine Oil

 

„

Engine Coolant

 

„

Hydraulic Oil

MECHANICAL

1. 

Grease Points 

— Ensure that the following Grease 

Points are greased, wiped down and capped:

• Thrust Collar

• Fingers

2. 

Hydraulics

• Spot check paint marks on fittings.
• Ensure that there are no leaks.

3. 

Retardant Spray System

• Fill with water and perform operational check.
• Verify no leaks.

4. 

Electrical (Cooling Fan)

• Verify fan cycles on when key is turned on 

(will remain on for 10s).

• Verify air flow direction is inward.

5. 

Lights

• Verify operation of all 6 machine lights.

6. 

Switches

• Verify proper operation of all switches.

7. 

Diagnotic Display

• Turn the ignition key clockwise to the ON position. All 

diagnostic display functions should be  available.

8. 

Aesthetics

• Paint Quality

- No bare spots
- No scratches

• Decals

- Readable
-Not torn or scratched

Summary of Contents for WHITEMAN Series



























Reviews:

No comments

Brands by name

Popular brands

Load more brands