manualshive.com logo in svg

MQ Multiquip WHITEMAN Series, Manual

Share
Download
MQ Multiquip WHITEMAN Series Manual Download Page 10

PAGE 10 — STXDF TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #0 (11/05/18) 

TOOLS NEEDED

The specialized tools listed in Table 1 are required to maintain and service the STX6DF ride-on trowel. Fleet technicians 

and servicing dealers must have these tools for efficient unit setup and component calibration.

Table 1. Setup, Calibration, and Diagnostic Tools

TOOL

DESCRIPTION

PART NO.

QTY

Tool Kit

Includes all tools listed below.

32061

1

CAN Gateway 

Cable/Canbus 

Jumper

Required to interface to the trowel MCU. 

Required for foot pedal calibration, pitch 

sync calibration, stroke cylinder calibration, 

engine fault code reading, diagnostics, etc.

22882/ 

22881

1

Set Up Jumper

Used to place the engine at full speed for 

component calibration and to simultaneously 

disable both the stroke follower and cold 

start mode.

42538

1

Service Tool 

(3 to 9 pin)

Required to interface to the Hatz ECU

42948

1

Summary of Contents for WHITEMAN Series



























Reviews:

No comments

Brands by name

Popular brands

Load more brands