manualshive.com logo in svg

MOVEK myMix, Owner'S Manual

Share
Download
MOVEK myMix Owner'S Manual Download Page 18

 

Volume

The default view on the CHANNEL screen is the volume control. The jog wheel adjusts 
channel volume from 0% to 100%. The default volume is 0%.

Tone

While on the CHANNEL screen, push the soft key labeled TONE to adjust simple Bass 
and Treble controls with the jog wheel. The default position is center.

Effect

Push the soft key labeled EFFECT to increase or decrease the amount of internal 
effect applied to each channel (the type of effect is selected in the EFFECTS screen 
under SETTINGS, if you have selected the effects type: none, no effect will be audible). 
The default position is 0% .

Pan

By pushing the soft key labeled PAN, you can control where the signal appears in the 
stereo field. 

Keep in mind that if you are listening on a 
mono device, panning a mono signal fully 
to the unused output will make the signal 
disappear.  This  also  applies  to  stereo 
signals  as  they  default  to  100%  left  and 
100% right. The default position is center.

For  a  stereo  signal,  the  panorama  turns 
into a BALANCE control. Each individual 
channel of a stereo signal is routed 100% 
to  the  left  or  right  by  default.  BALANCE 
allows  you  to  move  the  stereo  image  to 
either side. 

18

Summary of Contents for myMix





























Reviews:

No comments

Brands by name

Popular brands

Load more brands