background image

 

  ZIM12-00505 Rev. 1  

 

TransTech IV Service Manual 

 

 

SAFETY INFORMATION AND PRECAUTIONS

 

 

/!\ DANGER 

 

Vehicle exhaust gases contain Carbon Monoxide, which is a colorless and odorless 
lethal gas. 
Only run engines in well-ventilated areas and avoid breathing exhaust gases. 
Extended breathing of exhaust gases will cause serious injury or death. 

 

/!\ WARNING 

 

Exhaust gases, moving parts, hot surfaces are present during and after the vehicle’s 
engine is running. 
Read and understand the operator’s manual before using the TRANSTECH 
Service system.   
When using petroleum products always refer to the MSDS sheets and 
manufacturer’s instructions for the proper procedure to handle emergency 
medical treatment, cleanup, handling, and storage requirements. 
Improper use of the TRANSTECH Transmission Service System or exposure to exhaust 
gases can cause injury. 
Spilled transmission fluid on an engine can ignite. 
Avoid exposure to flames, sparks, hot engine parts, and other ignition sources. 
Always keep fully charge fire extinguisher nearby. The extinguisher should have 
a class B rating and be suitable for gasoline, chemical, and electrical fires. 
Cleanup any oil spills immediately. Dispose of contaminated cleanup material 
according to governing environmental laws.   
Never look directly into the air induction plenum or carburetor throat when the 
engine is operating.   
Always verify hose connections to the transmission’s oil cooler lines before 
starting the vehicle’s engine. 
Explosion or flame or exposure to flammable liquid and vapors can cause injury. 
Flammable liquid (transmission fluid) can splash out of reservoir when filling or when 
unit is being moved. 
Always keep Reservoir Cap secure except when filling reservoir. 
Explosion or flame can cause injury. 
Transmission cooling systems may maintain residual pressure in connection lines to 
and from transmission and cooler radiator even after the engine has been turned off. 
Wear safety goggles. 
Wear chemical resistant gloves when connecting or disconnecting fitting and 
adapters. 

Chemicals can cause harmful byproducts - do not add any chemicals to TransTech’s reservoir 
tank

.

 

Use only approved automatic transmission fluid. 
Do not swallow or ingest any chemicals. 
Use with adequate ventilation. Avoid breathing vapors. 
Do not store chemicals in or on the machine (other than automatic transmission 
fluid). 

Summary of Contents for 500-1125



































Reviews: