background image

Troubleshooting

Parts 

Service Parts for the TranTech™ III+ Transmission System.

Please refer to the part numbers below when ordering parts.

 

Part #   

 

Description

 

010-6060  

 

Reservoir Cap

020-8043 

 

Main power wires with battery clips

050-0095 

 

Filter spin on

050-0043 

 

Pump (Diesel and Gas/Petrol)

080-0230 

 

Female Quick Coupler

200-8667 

 

ICS (Intake System Cleaning) Kit -Complete

050-0016 

 

Pressure switch

ORDERING PARTS

Parts for the unit may be ordered by calling MotorVac Customer Service at (800) 841-8810 or  
(905) 615-8620  Please have your model and serial numbers available.

www.motorvac.com
[email protected]

[email protected]     www.motorvac.com

17

Symptom

Solution

The MCS 352 is not operational or trips breaker 
immediately.

Polarity is reversed on vehicle battery connection. 
Check connections for correct polarity. Check circuit 
breaker on the side of the cabinet.

Pressure Gauge on the MCS 352 displays maximum 
pressure upon start up.  

Output and Return hoses may be reversed. 
Pressure regulator may be fully closed.  Turn 
pressure regulator counterclockwise, turn timer to 
zero and check hoses for correct connection.

Rapid loss of fuel from the MCS 352 reservoir. 

Return hose connection may be incorrect, allowing 
fuel/detergent to return to the vehicle's fuel tank.

Start/Run switch is on but operation does not 
commence. Check Timer. 

If no time is set, then turn the Time knob to set the 
run time.

The MCS 352 performs poorly. 

Replace filter.  Check all hoses and wires for cuts or 
frays.

Summary of Contents for 500-0352























Reviews: