Motorola MC68HC05T16 Technical Data Manual Download

Page: 51 / 128

MC68HC05T16

MOTOROLA

5-9

TIMERS

Figure 5-4 Timer State Timing Diagram for Output Compare

Figure 5-5 Timer State Diagram for Timer Overflow

INTERNAL

PROCESSOR

CLOCK

T00

T01

T10

T11

COUNTER

(16 BIT)

INTERNAL

TIMER

CLOCKS

$F455

$F456

$F457

$F458

$F459

Note 1

Note 2

$F457

CPU writes $F457

OUTPUT COMPARE

COMPARE REGISTER

OUTPUT COMPARE

Flag and TCMP1, 2

Note:

1. The CPU write to the compare registers may take place at any time, but a compare only occurs at

the timer state T01. Thus a 4-cycle difference may exist between the write to the compare register
and the actual compare.

2. The output compare flag is set at the timer state T11 that follows the comparison match ($F547 in

this example).

LATCH

Note 1

INTERNAL

PROCESSOR

CLOCK

T00

T01

T10

T11

COUNTER

(16 BIT)

INTERNAL

TIMER

CLOCKS

$FFFE

$FFFF

$0000

$0001

$0002

Note:

TIMER

OVERFLOW

FLAG (TOF)

The TOF bit is set at timer state T11 (transition of counter from $FFFF to $0000).

It is cleared by a read of the timer status register during the internal processor
clock high time followed by a read of the counter low register.

TPG

Summary of Contents for MC68HC05T16

































































































































Search results

Summary of Contents for MC68HC05T16

Reviews:

Related manuals for MC68HC05T16

Brands by name

Popular brands

Motorola MC68HC05T16, Technical Data Manual

Search results

Summary of Contents for MC68HC05T16

Reviews:

Related manuals for MC68HC05T16

Brands by name

Popular brands