Motorola F5208 User Manual Download Page 49 | Manualshive

Page: 49 / 56

background image

33

Table 2 describes MW810 Mobile Workstation error mes-
sages that warn you about conditions that might prevent nor-
mal operation.

Table 2: MW810 Mobile Workstation Error Messages

Message

Do the following

“Vehicle Battery is
Low. The system will
shutdown in 3
minutes”.

The car battery voltage is below the
lower operational limit. Please save
your work before shutting down

“MW810 Mobile
Workstation CPU
temperature is high.
The system will
shutdown in 3
minutes”.

The internal temperature is higher
than the valid limit.
Please save your work before
shutting down. Never turn on the
MW810 Mobile Workstation until it
cools down to normal operating
temperature.

“MW810 Mobile
Workstation CPU
temperature is low.
The system will
shutdown in 3
minutes”.

The internal temperature is below the
valid limit.
Please save your work before
shutting down. Never turn on the
MW810 Mobile Workstation until it
heats up to normal operating
temperature.

“PC Card error was
detected. Please
remove the PC Card
device and then press
OK”

Card Bus over-current is discovered.
Please refer to service for re-
installing the PC Card. Press OK to
confirm the operation.

MW810 Mobile
Workstation hard drive
heater may be
malfunctioning.

Heater over-current is discovered.
Please, contact your system
administrator.

Warranty very small format.book Page 33 Sunday, April 18, 2010 7:49 PM

«
...
47
48
49
50
51
...
»

Summary of Contents for F5208

























































Reviews:

No comments

Related manuals for F5208

Brand: VALKPC Pages: 20

Pavilion Slimline s5500 - Desktop PC

Brand: Compaq Pages: 36

Ferrari 1000 Series

Brand: Acer Pages: 123

Brand: Acer Pages: 112

Brand: Vivo Pages: 12

Brand: Casio Pages: 133

Brand: Dell Pages: 21

Brand: Dell Pages: 2

Studio XPS 8100

Brand: Dell Pages: 8

Brand: Dell Pages: 31

Brand: Dell Pages: 38

Brand: Dell Pages: 34

Brand: Dell Pages: 38

Brand: Dell Pages: 30

Brand: Dell Pages: 30

Brand: Dell Pages: 64

Brand: Dell Pages: 40

Studio XPS 435 MT

Brand: Dell Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands