Motorola APX8500 Manual Download

Page: 33 / 273

GETTING STARTED

Preparing Your Radio for Use

Validating Compatibility During Power Up

The radio validates and updates the software and hardware of your control head(s) during power up. During
validation, the display shows

Maintenance Mode Remote Device

promptly followed by other maintenance

statuses.

Procedure:

When the display shows

Update done Please reset

upon completion, press the

Power On/Off

Button to

reset:

When the display shows

Update failed Please reset

when it fails to update, press the

Power On/Off

Button

to reset.

If the software updates are completed, the radio runs the usual power-up operation.

If the updates are incomplete, the radio runs the Maintenance Mode and the display shows

Maintenance

Mode Remote Device

; promptly followed by other maintenance statuses again.

Summary of Contents for APX8500


















































































































































































































































































Search results

Summary of Contents for APX8500

Reviews:

Related manuals for APX8500

Brands by name

Popular brands

Motorola APX8500, Manual

Search results

Summary of Contents for APX8500

Reviews:

Related manuals for APX8500

Brands by name

Popular brands