Motorola APX8500 Manual Download

Page: 255 / 273

NEXT >

< PREV

CONTENTS

UTILITIES

Instant Recall

This feature allows the user to save the last received
call and playback the recorded call.

Saving and Playback Calls

Follow the procedure below to save the recorded
calls using the preprogrammed

Record Playback

button:

Procedure:

[Preprogrammed Button]

Long press the preprogrammed

Record Playback

button to save the recorded calls.

Radio displays

Audio Saved

momentarily.

Radio plays the saved call automatically if call
saving is successful.

A tone sounds if call saving is not successful.

Follow the procedure below to playback the saved
calls using the preprogrammed

Record Playback

button:

Short press the preprogrammed

Record

Playback

button to playback the saved calls.

Short press the preprogrammed

Record

Playback

button again to skip to the next saved

call. If there is only a single saved call, the
playback skips to the end of the call.

Radio auto playback the most recent incoming call
followed by saved calls in chronological order.

Radio displays the playback status

255

Summary of Contents for APX8500


















































































































































































































































































Search results

Summary of Contents for APX8500

Reviews:

Related manuals for APX8500

Brands by name

Popular brands

Motorola APX8500, Manual

Search results

Summary of Contents for APX8500

Reviews:

Related manuals for APX8500

Brands by name

Popular brands