manualshive.com logo in svg

Motorola 68230 - Vanguard 300 DSU/CSU, Operator'S Manual, Page: 49 / 79

Share
Download
Motorola 68230 - Vanguard 300 DSU/CSU Operator'S Manual Download Page 49

ETH  

Identifies an 
Ethernet interface 
port. 

 

Port Type: (Select 
one of either 
Ethernet or Token 
Ring) 

TR  

Identifies a Token 
Ring interface port. 

 

From the Configure menu, select Route Selection. Then: 
Configure the following. 

Prompt:  

Enter:  

Result/Description 

Entry Number: 

1  

References this 
table record. 

Address:  

100*  

Identifies the 
address to be 
routed. 

5  

#1 Destination: 

P1  

Identifies Port 1 of 
this node. 

The Route 
Selection table 
appears. 

From the Configure menu, select Mnemonic table. Then: 
Configure the following. 

Prompt:  

Enter:  

Result/Description 

Entry Number: 

1  

References this 
table record. 

Mnemonic name: 

LAN100  

Identifies the 
mnemonic name. 

6  

Call parameters: 

10094  

Identifies the 
location to send the 
autocall to. The 
convention is to 
identify the node 
and port number in 
this parameter. 

The Mnemonic 
table appears. 

 

Follow these steps to configure Node 300 as shown in Figure 3-3. 

Summary of Contents for 68230 - Vanguard 300 DSU/CSU
















































































Reviews:

No comments