manualshive.com logo in svg

Motorola 68230 - Vanguard 300 DSU/CSU, Operator'S Manual, Page: 48 / 79

Share
Download
Motorola 68230 - Vanguard 300 DSU/CSU Operator'S Manual Download Page 48

From the Configure IP menu, select Interfaces. Then: 
Configure the following. 

Prompt:  

Enter:  

Result/Description 

Entry Number: 

1  

References this 
table record. 

Interface Number: 

1  

Identifies the router 
interface number 
being configured. 

IP Address:  

219.2.83.200   Identifies the IP 

address associated 
with this interface. 

Entry Number: 

2  

References this 
table record. 

Interface Number: 

6  

Identifies the router 
interface number 
being configured. 

3  

IP Address:  

200.1.2.200  

Identifies the IP 
address associated 
with this interface. 

The Interfaces 
menu appears. 

From the Configure menu, select Port record. Then: 
Configure the following. 

Prompt:  

Enter:  

Result/Description 

Port Number: 

1  

Identifies port 
number 1 of node 
200. 

Port Type:  

X25  

Identifies an X.25 
interface port. 

Clock Source: 

Ext  

Identifies that the 
clock will not be 
generated by this 
Vanguard 300 on 
this port. 

Link Address: 

DTE  

Defines the logical 
address of the port 
for X.25 operation. 

4  

Port Number: 

5  

Identifies port 
number 5 of node 
200. 

The Port record 
appears. 

 

Summary of Contents for 68230 - Vanguard 300 DSU/CSU
















































































Reviews:

No comments