manualshive.com logo in svg

Motorola 68230 - Vanguard 300 DSU/CSU, Operator'S Manual, Page: 32 / 79

Share
Download
Motorola 68230 - Vanguard 300 DSU/CSU Operator'S Manual Download Page 32

From the Configure menu, select Configure Router -
> Configure IPX -> Parameters. Then configure the 
following. 

Prompt 

Enter 

Result/Description 

5 

Enable IPX: 

Enabled 

Enables overall 
routing of Internal 
Protocol Exchange 
(IPX) packets. 
Enables Novell 
workstations to 
connect to remote 
file and printer 
services. 

The Parameters 
record appears. 

From the Configure menu, select Configure Router -
> Configure IPX -> Interfaces. Then configure the 
following. 

Prompt 

Enter 

Result/Description 

Interface 
Number: 

1 

Identifies the router 
interface number 
being configured. 

Network 
Number: 

00000100 

Identifies the four-
byte Novell 
network number 
assigned to the 
network attached to 
this interface. 

Interface 
Enable: 

Enabled 

Enables IPX 
routing on this 
interface. 

Interface 
Number: 

5 

Identifies the router 
interface number 
being configured. 

Network 
Number: 

00000101 

Identifies the four-
byte Novell 
network number 
assigned to the 
network attached to 
this interface. 

6 

Interface 
Enable: 

Enabled 

Enables the router 
interface. 

The Interfaces 
record appears. 

 

Summary of Contents for 68230 - Vanguard 300 DSU/CSU
















































































Reviews:

No comments