background image

1A

1B

1B

4A
4A
4B
4B
5A

5B
6

8B

8A

10A

8B
9A
9A
9A
9B

EN

EN

00. CONTENT

01. SAFETY INSTRUCTIONS

INDEX

This product is certified in accordance with European 

Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the 

European Parliament and of the Council, of 8 June 2011, on 

the restriction of the use of certain hazardous substances 

in electrical and electronic equipment and with Delegated 

Directive (EU) 2015/863 from Commission.
(Applicable in countries with recycling systems).

This marking on the product or literature indicates that the 

product and electronic accessories (eg. Charger, USB cable, 

electronic material, controls, etc.) should not be disposed 

of as other household waste at the end of its useful life. To 

avoid possible harm to the environment or human health 

resulting from the uncontrolled disposal of waste, separate 

these items from other types of waste and recycle them 

responsibly to promote the sustainable reuse of material 

resources. Home users should contact the dealer where 

they purchased this product or the National Environment 

Agency for details on where and how they can take these 

items for environmentally safe recycling. Business users 

should contact their vendor and check the terms and 

conditions of the purchase agreement. This product and 

its electronic accessories should not be mixed with other 

commercial waste.
This marking indicates that the product and electronic 

accessories (eg. charger, USB cable, electronic material, 

controls, etc.) are susceptible to electric shock by direct or 

indirect contact with electricity. Be cautious when handling 

the product and observe all safety procedures in this manual.

ATTENTION:

MF2020

TECHNICAL CHARACTERISTICS

NUMBER OF SENSORS
IDENTIFICATION OF PARTS
DIMENSIONS AND DESCRIPTION

CARE DURING INSTALLATION
INSTALLATION

OPERATING MODE

CONNECTION SCHEME

INSTRUCTIONS FOR CONSUMERS AND SPECIALIZED TECHNICIANS

01. SAFETY INSTRUCTIONS

02. THE PRODUCT

03. INSTALLATION

05. OPERATION

04. CONNECTIONS

06. TROUBLESHOOTING

CHANGE OPERATING MODE
RELAY OUTPUT

TEST INPUT
TIME DIAGRAM

LED SIGNALING

Summary of Contents for MF2020












Reviews: