background image

4A

4B

06

A

A

B

B

05

07

08

04

EN

EN

A

?? 

mm

B

A - 

20mm

Operator must be installed with a small inclination , to prevent water infiltration through the 

extension arm.

For this, the front support must be fixed to the gate with a height lower than the height of the 

rear support. See example below:

Example:

 

• If the height of the rear bracket (dimension A)is set at 600 mm, then the height of the front 

bracket (dimension B) will be 580 mm (600mm-20mm).

Dimension A

 • 

Vertical distance from the floor to the top of the rear support.

Dimension B

 • 

Vertical distance from the floor to the top of the front support.

• Set 

dimension A

 (this can be any size of your choice).

• After you set 

dimension A

, subtract 

20mm

 to find 

dimension B

.

It is very important that these dimensions are respected! Only this way can be assured the 

correct functioning and durability of the operators!

It is also very important to have a levelled ground/terrain!

VERTICAL INSTALLATION DIMENSIONS

03. OPERATOR

TECHNICAL SPECIFICATIONS

LOCK/UNLOCK MOTOR

04. INSTALLATION

Place the unlocking key in the slot signed on 

image 05 (motor installed on the left) or 06 

(motor installed on the right). 

Turn the key to lock or unlock the motor (07).

08

JAG 400 || 600

 dimensions are the following:

04

1375mm

 || 

1775mm

975mm

 || 

1175mm

110mm

Summary of Contents for JAG Series














Reviews: