manualshive.com logo in svg

Motor City Wash Works AIR ONE PROFILER, Installation Manual

Share
Download
Motor City Wash Works AIR ONE PROFILER Installation Manual Download Page 11

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. 

Phone: 248.313.0272 ▪ Fax: 248. 313.0271 

        

REVISION 5-20-21

                            

www.motorcitywashworks.com

                                                 

11

 

 

 

 

 

Pic #14-b: Air Panel Connections (External) 

 

 

 

Locate

 the boxes containing the 

COLOR SKINZ™ 

covers and install on each leg and photo-eye tree (see below).

 

 

        

                                          

 

                 Pic #15 Color Skinz™                                                                                              Pic #16 Color Skinz™ 

 

 

SELECT THE 

PROPER COLOR 
SKINZ™ COVER. 

SNAP ONE SIDE OF 

THE LIP, SLIDE 

THE COVER 

AROUND THE LEG 

AND FINALLY 

SNAP THE 

SECOND LIP PAST 

THE EXTRUSION 

EDGE (see Picture 

#16) 

ENTRANCE DOWN 

EXHAUST 

ENTRANCE UP 

EXIT UP 

EXIT DOWN 

COLOR-CODED 

LEGEND 

MAIN AIR INLET 

Summary of Contents for AIR ONE PROFILER








































Reviews:

No comments

Brands by name

Popular brands

Load more brands