MOTO GUZZI V750 IE Service Station Manual Download Page 62

Page: 62 / 113

•

Valve guides need to be knocked out

tapping from the inside with punch and

mallet; heat the head up to approxi-

mately 50-60 °C to aid removal.

Specific tooling

19.92.60.20

Punch for cap installation on valve

guide.

Checking the rocker arms

•

Check that the bolt surface that con-

tacts the rockers is not exceedingly

worn.

•

Check the rocker to valve and rocker to

rod contact surfaces.

Inspecting the springs and half-cones

With the assembly installed (retainers, springs, valves and cotters in the heads), the compressed ex-

ternal springs should measure 36 mm (1.4173 in). Please note that the valves should have a remaining

lift of 1 mm (0.039 in) when fully open before the internal spring becomes fully compressed. If not so,

remove or add shims until achieving this condition.

Engine

Engine V750 IE

ENG - 62

Summary of Contents for V750 IE


















































































































Search results

Summary of Contents for V750 IE

Reviews:

Related manuals for V750 IE

Brands by name

Popular brands

MOTO GUZZI V750 IE, Service Station Manual

Search results

Summary of Contents for V750 IE

Reviews:

Related manuals for V750 IE

Brands by name

Popular brands