MOTO GUZZI V750 IE Service Station Manual Download Page 83

Page: 83 / 113

Fitting the piston

•

To refit the piston into the connecting

rod small end, heat up the piston in an

oil bath up to approximately 60°C (140°

F); this will cause the piston to expand

slightly and facilitate pin insertion.

•

Insert the retaining clip into the piston

and fit the specified pin insertion tool to

the piston.

•

Position the piston with the tool attach-

ed on the connecting rod in order to

install the pin.

•

When finished, remove the tool and in-

sert the second snap ring that closes

the piston pin seat, after protecting the

cylinder seat.

CAUTION

MOUNTING POSITION IS INDICATED BY AN ARROW
POINTING IN THE DIRECTION OF TRAVEL

Engine V750 IE

Engine

ENG - 83

Summary of Contents for V750 IE


















































































































Search results

Summary of Contents for V750 IE

Reviews:

Related manuals for V750 IE

Brands by name

Popular brands

MOTO GUZZI V750 IE, Service Station Manual

Search results

Summary of Contents for V750 IE

Reviews:

Related manuals for V750 IE

Brands by name

Popular brands