MOTO GUZZI V750 IE Service Station Manual Download Page 106

Page: 106 / 113

•

External rotor seat thickness 15.030 -

15.070 mm (0.5917 - 0.5933 in).

EXTERNAL ROTOR

Check that the inner and outer surfaces and the

flat faces are not scored, damaged or dented; if

they are, replace both rotors.

External rotor specifications:

•

outer Ø 40.540 - 40.570 mm (1.5960 -

1.5972 in);

•

inner Ø 24.205 - 24.230 mm (0.9529 -

0.9539 in);

•

thickness 14.960 - 14.990 mm (0.5890

- 0.5902 in).

INTERNAL ROTOR

Check that the inner and outer surfaces and the

flat faces are not scored, damaged or dented; if

they are, replace both rotors.

Internal rotor specifications:

•

outer Ø 29.745 - 29.770 mm (1.1711 -

1.1720 in);

•

inner Ø 12.000 - 12.018 mm (0.4724 -

0.4731 in);

•

thickness 14.960 - 14.990 mm (0.5890

- 0.5902 in).

NEEDLE BEARINGS

Make sure the needle rollers of the bearings are

not damaged; if they are, replace the bearings.

Engine

Engine V750 IE

ENG - 106

Summary of Contents for V750 IE


















































































































Search results

Summary of Contents for V750 IE

Reviews:

Related manuals for V750 IE

Brands by name

Popular brands

MOTO GUZZI V750 IE, Service Station Manual

Search results

Summary of Contents for V750 IE

Reviews:

Related manuals for V750 IE

Brands by name

Popular brands