Morso P30, Instructions For Installation And Use Manual, Page: 7 / 21

12 13
Sprog
Sprog
A
A
B
B
A-A (1 : 10)
B-B (1 : 10)
Revisions Rev. Sign.:
Title:
Drawing no.:
1:5
Montering til skorsten
Morsø P30
RSV
29.10.12
A3
31.0
ERROR!:materiale
Date of print: 30-10-2012
U:\udv\Tegninger\Pilleovn\Morsø P30\Morsø P30 kofiguration 01A\070-MO-001A.sldasm
P30-08 a
Itemno.:
This drawing is Morsø Jernstøberi A/S' property and must not be sold, lended or copied without any written authorization from the company.
Material:
Weight kg:
Model no.
Drawingtype:
Location of file:
Scale:
Format:
Released:
Construction:
Date:
This type of installation does not need an insulated chimney, as part of the flue is fitted internally
in the house, and the other part is inside an existing chimney. Remember to only use approved
duct tubes.
A T-piece with built-in inspection cover must be fitted at the base of the chimney. Installing a 90°
bend as the first piece is not recommended, as over a short time ash will hinder smoke flow and
thus create problems for the draught to the stove. Note here the use of 2 no. 45° bends to ensure
that ash drops into the T-piece with an inspection cover.
Chimney installation, Example 5
Support plate
Cowl
Installing a 90° bend is
not recommended, as
over a short time ash will
hinder smoke flow and
thus create problems for
the draught to the stove.
T-piece for condensate
45° bend
2.0 Stoking technique/ Use of your stove
2.2 Construction of the pellet stove.
The drawing above shows the internal parts of a pellet stove. After filling the hopper (7), timber
pellets are transferred by the auger (1) to the burn pot (3). Ignition is initiated by the ignition
tube (2), which heats the air.
2.1 General
The pellet stove must be installed in a dry environment. As it is controlled by an electronic prin-
ted circuit board, combustion is completely automatic and controlled.
The printed circuit board regulates the lighting phases, 5 power steps, extinguishing and thus
guarantee safe function.
The majority of the ash created during combustion of the pellets drops into the ash drawer via
the burn pot used for combustion.
In any event, check the burn pot daily, as not all pellets are of a high standard and can therefore
leave remnants that can be difficult to remove.
The glass is provided with a special self-cleaner. A slight greyish patina is, however, unavoidably
formed on the glass after some hours’ operation.
1. Pellet auger
2. Ignition tube
3. Burn pot
4. Exhaust flue
5. Heat-resisting steel heat exchanger
6. Pellet hopper
7. Smoke deflector
8. Flue gas outlet A
A
B
B
A-A (1 : 10)
B-B (1 : 10)
Revisions Rev. Sign.:
Title:
Drawing no.:
1:5
Montering til skorsten
Morsø P30
RSV 29.10.12
A3
31.0
ERROR!:materiale
Date of print: 30-10-2012 U:\udv\Tegninger\Pilleovn\Morsø P30\Morsø P30 kofiguration 01A\070-MO-001A.sldasm
P30-08 a
Itemno.:
This drawing is Morsø Jernstøberi A/S' property and must not be sold, lended or copied without any written authorization from the company.
Material:
Weight kg:
Model no.
Drawingtype:
Location of file:
Scale:
Format:
Released:
Construction:
Date:
A
A
B
B
A-A (1 : 10)
B-B (1 : 10)
Revisions Rev. Sign.:
Title:
Drawing no.:
1:5
Montering til skorsten
Morsø P30
RSV
29.10.12
A3
31.0
ERROR!:materiale
Date of print: 30-10-2012
U:\udv\Tegninger\Pilleovn\Morsø P30\Morsø P30 kofiguration 01A\070-MO-001A.sldasm
P30-08 a
Itemno.:
This drawing is Morsø Jernstøberi A/S' property and must not be sold, lended or copied without any written authorization from the company.
Material:
Weight kg:
Model no.
Drawingtype:
Location of file:
Scale:
Format:
Released:
Construction:
Date:
1
2
6
5
7
8
4
3