manualshive.com logo in svg

Mopar K6860899, Instruction Manual, Page: 106 / 121

Share
Download
Mopar K6860899 Instruction Manual Download Page 106

2

6.

Remove the drivers side lower insrument panel (IP)
bezel fastener (3).

7.

Carefully pry the bezel (2) away from the IP (1) disen­
gaging the retainers from the IP.

8.

At the point just above where the headliner and the
storage tray meet, carefully cut a small slot in the
headliner to allow the WiFi router harness to be fed
through and routed.

9.

Carefully route the harness through the slot cut in the
headliner.

10. Route the harness along the leading edge at the wind­

shield and tuck under the headliner.

NOTE: Do not secure the harness to the airbag or re­
lated components.

11. Route and secure the harness down along the driver

side A­pillar body side and secure.

12. Route the haness through the IP lower bezel.
13. Remove the connetor (2) from the junction block (1)

under the driver side IP.

14. Using the appropriate pin extraction tool, remove the

pin from cavity 3 of the connector.

Oct 16, 2009

K6860899 Rev. 1

Summary of Contents for K6860899


























































































































Reviews:

No comments