background image

MP-201 Multi-Pedal Manual

Firmware v2.0 Addendum

Changes to Channel Mode GATE:

Previously the most simple of MP-201 Channel Modes, the humble 

GATE

 could be either On or Off, Momentary 

or Latching. Now 

GATE

 Mode is perhaps the most powerful and richly-featured Channel Mode of them all.

The first change you will notice is the 

GATE SOURCE

 selection. Options are 

FOOT SWITCH

MIDI NOTES

, or 

PEDAL CV

.

FOOT SWITCH

 preserves the functionality of GATE Mode in firmware v1: You can set 

FS MODE

 to Latching or 

Momentary, to control how the channel toggles On/Off in response to the foot switch, and you can set 

INITIALSTATE

 to control whether the gate is On or Off when the preset is loaded. 

For Momentary Gates, 

INITIALSTATE

 sets whether the gate is Normally-Off (Momentary-On) or Normally-On 

(Momentary-Off).

If 

GATE SOURCE

 is set to 

MIDI NOTES

, then the channel behaves as a Normally-Off, Momentary-On Gate 

which turns on in response to MIDI notes on the selected MIDI channel.  

VELO TRIGGER

 allows you to set a MIDI Velocity (1-127) below which the Gate will not turn on. 

 

TRIGGER MODE

 - controls how the Gate behaves in response to multiple MIDI notes at a time.  

LEGATO:

 In this Trigger Mode, the Gate will turn on in response to the first MIDI NoteOn message, and will 

remain On continuously for as long as any notes remain held.  When the last NoteOff message is received and 
there are no notes on the note stack, then the Gate will turn Off. 

RETRIGGER:

 The Gate will turn momentarily Off and then On again for each new MIDI note.  If the Gate is 

controlling an Envelope, this will cause the Envelope Generator to fire with each new note played, even if other 
notes are still held. These Trigger Modes are designed to behave similarly to the Gate functions of most 
monophonic analog synthesizers.

The final 

GATE SOURCE

 option is 

PEDAL CV

.  This mode reads the scaled voltage coming from the MP-201 

Foot Pedal, and allows you to set a 

THRESHOLD

 above which the Gate will turn on, and below which it will turn 

off.  

You can set 

HEEL VALUE 

and 

TOE VALUE

 parameters to adjust exactly the point at which the Gate will act, 

including setting 

TOE VALUE

 less than 

HEEL VALUE

 in order to reverse the Off and On directions (e.g. to have 

a Gate that is On when the pedal is in the Heel position and Off when the pedal is moved to the Toe position).

When Gate Source is set to MIDI Notes or Pedal CV, the Channel On/Off footswitch does not turn the Gate on 
and off (as it does when Gate Source = Foot Switch); instead, the Channel On/Off footswitch disables or enables 
triggering of the gate by the selected Gate Source.  That is to say, that the footswitch toggles whether or not the 
Gate will respond to MIDI Notes or to Pedal movements.  When Gate response is disabled, this is indicated by 
"---" shown on the LCD where the Channel Mode (

GATE

,

 EG

) would normally be displayed.  

The 

GATE / EG

 parameter allows you to select 

GATE

 or 

ENVELOPE

 

CV

 output for this channel.  Envelope 

Generation is a major new feature for the MP-201.  Envelopes appear as CV Output only; the MIDI output for 
Gate channels is the same regardless of 

GATE / EG

 setting.

Page | 3

Specifications subject to change without notice

moogmusic.com

Summary of Contents for MP-201 Multi-Pedal













Reviews: