background image

Page 13

BF36-SS and ST Gas Fireplace

Part No. XG0712 - 031811

f i r e    f e a t u r e 

Operation -  Model BF-SS

For Your Safety - READ BEFORE LIGHTING:

To Turn Off  Gas To Appliance:

Lighting  Instructions:

  If you cannot reach your gas supplier, call the Fire De-

partment.

C.

  Use only your hand to push in or turn the gas control knob. 

Never use tools. If  the knob will not push in or turn by hand, 

don't try to repair it, call a qualified service technician. Force 

or attempt to repair may result in a fire or explosion.

D.

  Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect the 

appliance and to replace any part of the control system, and 

any gas control which has been under water.

A. 

This appliance is equipped with an ignition system that 

lights the pilot burner automatically. 

Do not attempt to light 

the pilot by hand.

B.  BEFORE LIGHTING

 smell all around the appliance area for 

gas.  Be sure to smell next to the floor because some gas is 

heavier than air and will settle on the floor.

 

What To Do If You Smell Gas:

  Do not try to light any appliance.

  Do not touch any electrical switch; do not use any phone 

in your building.

  Immediately call your gas supplier from a neighbour's 

phone. Follow the gas supplier's instructions.

1. 

Turn off remote switch.

2. 

Remove the lower Horizontal access panel..

3. 

Turn the switch on the gas control to "Off".

4. 

Replace the lower Horizontal access panel.

1.

 

STOP!  

Read the safety information above on this label.

2.

  Remove the lower Horizontal access panel.

3.

  Turn switch on the gas control to OFF".

4.

  Wait 5 minutes to clear out any gas.  If you smell gas,

 

STOP! 

Follow "B" in the safety information above on this 

label.  If you don't smell gas, go to the next step.

5.

  Turn switch on the gas control to "ON".

 NOTE:

 This unit is 

equipped with an ignition system that lights the pilot burner 
automatically. 

Do not attempt to light the pilot by hand.

6.

  Turn on wall switch.

7.  

Replace the lower Horizontal access panel.

8.

  If the fireplace does not operate, follow the instructions "To 

Turn Off Gas To Appliance" and call your service technician 
or gas supplier.

with Honeywell  Electronic Ignition

WARNING:

 

If you do not follow these instructions exactly, a fire or explosion may result 

causing property damage, personal injury or loss of life.

Gas

Inlet

Gas Control Switch

Shown in "On" Position

Summary of Contents for BF36-SS



















Reviews: