manualshive.com logo in svg

Montag C06B, Operation Manual, Page: 20 / 33

Share
Download
Montag C06B Operation Manual Download Page 20

20

3.3.10 INSTALL SAFETY CHAINS 

Follow this procedure if chains were not installed at the factory.

1. 

Install 26 in. (660 mm) short chain (A) and long chains (B) 

as shown. Place four ½ x 2½ inch bolts (C) from front of cart 

through plate, long chain, washer and lock nut.

2. 

Tighten bolts to 90 lb/ft (121 Nm) of torque.

3. 

Install clevis hook on end of each long chain.

3.3.11 INSTALL FLOATING SADDLES (DRY FERTILIZER USE ONLY)

Note: Four floating saddles (A) are provided on standard carts. 

1. 

Position  floating  saddles  (A)  under  brackets  on  cart  arms 

with short sides of arms to outside of cart.  

Note: Floating saddles must move freely to accommodate 

movement of hoses. Do not fully tighten lock nuts. 

2. 

Assemble  Hose  Guide  Strap  assemblies  (E)  as  shown, 

placed directly under the saddles, shorter strap to the front, 

longer strap to the rear of cart. Tighten 3/8" lock nuts so they 

are snug.

3. 

Install ⅝ x 1½ inch bolt (B) ⅝ inch spacers (C) and ⅝ inch 

lock nut (D). Tighten lock nut so it is snug, but saddle can still 

move freely. 

4. 

Repeat steps 1-2 for other side.

3.4 GEN I SYSTEM ASSEMBLY

  

3.4.1 INSTALL GEN I SKID ON CART (WITHOUT OPTIONAL WEIGH BARS)

Prevent death or serious injury.

Dry fertilizer skid weighs approximately 2000 

lbs. (907 kg).

Use adequate lifting and support devices.

1. 

Carefully position skid onto cart, with skid frame fully aligned 

with cart frame and ends of frames flush with each other.

Note: Install U-bolts facing up, with nuts on top. If U-bolts are 

installed facing down, there may be interference with cart arms.

Summary of Contents for C06B


































Reviews:

No comments