Monessen Hearth MJ22NIF/PIF Installation & Owner'S Manual Download Page 27

27

Monessen  • Mojo Installation/Owner’s Manual  •  4623-900  Rev. D  • 04/21

B.  Limited Lifetime Warranty

 (continued)

WARRANTY CONDITIONS:

•  Because HHT cannot control the quality of any Products sold by unauthorized sellers, this Warranty only covers Products that are 

purchased through an HHT authorized dealer or distributor unless otherwise prohibited by law; a list of HHT authorized dealers 

is available on the HHT branded websites. 

•  This Warranty is only valid while the applicable Product remains at the site of original installation. 
•  This Warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the applicable Product is 

authorized to sell applicable Product. 

•  Contact your installing distributor or dealer for Warranty service. If the installing dealer or distributor is unable to provide 

necessary parts, contact the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking 

Warranty service from a dealer other than the dealer from whom you originally purchased the applicable Product.

•  No HHT consumer should bear cost of warranty service or costs incurred while servicing warranty claims (i.e., travel, gas, or 

mileage) when the service is performed within the terms of this Warranty. Check with your dealer or distributor in advance for 

any costs to you when arranging a warranty call. Travel and shipping charges for parts are not covered by this Warranty. 

WARRANTY EXCLUSIONS:

This Warranty does not cover the following:

•  Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and exterior surface 

finishes may occur. This is not a flaw and is not covered under the Warranty. 

•  Damage  to  printed,  plated,  or  enameled  surfaces  caused  by  fingerprints,  accidents,  misuse,  scratches,  melted  items  or  other 

external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes. 

•  Repair or replacement of parts that are subject to normal wear and tear during the Warranty Period are not covered. These parts 

include: paint, wood and pellet gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass. 

•  Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to 

this noise are not covered by this Warranty.

•  Damages  resulting  from:  (1)  failure  to  install,  operate,  or  maintain  the  applicable  Product  in  accordance  with  the  installation 

instructions,  operating  instructions,  and  listing  agent  identification  label  furnished  with  the  applicable  Product;  (2)  failure  to 

install the applicable Product in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, 

abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/incorrectly performed 

repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly sealed constructions, 

insufficient make-up air supply, or handling devices such as exhaust fans or forced air furnaces or other such causes; (6) use of fuels 

other than those specified in the operation instructions; (7) installation or use of components not supplied with the applicable 

Product or any other components not expressly authorized and approved by HHT; (8) modification of the appliance not expressly 

authorized and approved by HHT in writing; and/or (9) interruptions or fluctuations of electrical power supply to the applicable 

Product. 

•  Non-HHT venting components, hearth connections or other accessories used in conjunction with the applicable Product. 

•  Any part of a pre-existing fireplace system in which an insert or a decorative gas applicable Product is installed. 

•  HHT’s obligation under this Warranty does not extend to the Product’s capability to heat the desired space. Information is provided 

to assist the consumer and the dealer in selecting the proper Product for the application. Consideration must be given to the 

Product location and configuration, environmental conditions, insulation and air tightness of the structure. 

This warranty is void if:

•  The  applicable  Product  has  been  over-fired,  operated  in  atmospheres  contaminated  by  chlorine,  fluorine,  or  other  damaging 

chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, deformation/warping of interior cast iron 

structure or components, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes. 

•  The applicable Product is subjected to prolonged periods of dampness or condensation. 

•  There is any damage to the applicable Product due to water or weather damage which is the result of, but not limited to, improper 

chimney or venting installation. 

LIMITATIONS OF REMEDIES AND LIABILITY:

•  EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED 

HEREIN. The owner’s exclusive remedy and HHT’s sole obligation under this Warranty or in contract, tort or otherwise, shall be 

limited to replacement of the Component Part(s), repair of the Component Part(s), or refund of the original purchase price of the 

applicable Product(s), as specified above; provided, however, that (i) if HHT is unable to provide replacement of the Component 

Part(s) and repair of the Component Part(s) is not commercially practicable or cannot be timely made, or (ii) the customer is 

willing to accept a refund of the purchase price of the applicable Product(s), HHT may discharge all such obligations by refunding 

the purchase price of the applicable Product. In no event will HHT be liable for any incidental or consequential damages caused 

by defects in the applicable Product. Some States do not allow the exclusion or limitation of incidental or consequential damages, 

so the above limitation or exclusion may not apply to you. This Warranty gives you specific legal rights and you may also have 

other rights which vary from State to State. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE 

EXPRESSED WARRANTY SPECIFIED ABOVE FOR THE APPLICABLE PRODUCT. Some States do not allow limitations on how long an 

implied warranty lasts, so the above limitation may not apply to you. 

Page 2 of 2

4021-645L  10/20

Summary of Contents for MJ22NIF/PIF
















































Reviews: