molex TCDEC-8B4B-D1U-G8 Original Instructions Manual Download Page 65

Page: 65 / 187

EtherNet/IP™ CIP Safety™ IP67 HarshIO 600



IP67 Safety Digital I/O Modules

Network Status LED (NET)

LED
State

Status

Description

OFF

No Power /
No IP Address

The module is not online.

The module may not be powered, look at Module Status LED (MOD).

FLASHING
GREEN

Online /
Not Connected

The module is Online but has no connection in the established state
(IDLE mode).

GREEN

Link OK / Online
/ Connected

The module is Online and has connections in the established state
(EXECUTING mode).

FLASHING
RED

Connection
Time-out

One or more I/O connections are in the timed

–out state.

RED

Critical link
failure

Failed communication device. The module has detected an error that
has rendered it incapable of communicating on the network.

FLASHING

RED

GREEN

Communication
faulted

A specific communication faulted (device uses this indication to allow
maintenance personnel commissioning the TUNID in a safety device).

Module Configuration Lock Status LED (LOCK)

LED
State

Mode

Description

OFF

either no
configuration or

either
configured by a
CIP Safety
Originator

The module is not configured or has been configured by a safety
originator (FW Open Type 1).

YELLOW

Configuration
Locked

Valid configuration received and locked.

FLASHING

YELLOW

Configuration
not Locked

Valid configuration received and not locked.

RED

Module faults



Memory key missing



Bad safety configuration

Summary of Contents for TCDEC-8B4B-D1U-G8




























































































































































































Search results

Summary of Contents for TCDEC-8B4B-D1U-G8

Reviews:

Related manuals for TCDEC-8B4B-D1U-G8

Brands by name

Popular brands

molex TCDEC-8B4B-D1U-G8, Original Instructions Manual

Search results

Summary of Contents for TCDEC-8B4B-D1U-G8

Reviews:

Related manuals for TCDEC-8B4B-D1U-G8

Brands by name

Popular brands