Mohawk V-035-A-X Page 17 Operation And Maintenance Manual Download | Manualshive

Page: 17 / 112

background image

MV-A00000920

MOHAWK V-A SERIES: VERTICAL RISE DRIVE-ON MANUAL

35,000 - 64,000 LB MODEL

3-3

3.3.

Owner/Employer Responsibilities

The owner/employer:

Shall ensure that lift operators are qualified and that they are trained in
the safe use and operation of the lift using the manufacturer’s operating
instructions; ALI/SM, “Lifting It Right” safety manual; ALI/ST, “Safety
Tips” card; ANSI/ALI ALOIM, Standard for Automotive Lifts – Safety
Requirements for Operation, Inspection and Maintenance; ALI/WL
Series, ALI Uniform Warning Label Decals/Placards; and in the case of
frame engaging lifts, ALI/LP-

Guide, “Quick Reference Guide – Vehicle

Lifting Points for Fr

ame Engaging Lifts”.

Shall establish procedures to periodically inspect the lift in accordance
with the lift manufacturer’s instructions or ANSI/ALI ALOIM, Standard for
Automotive Lifts

– Safety Requirements for Operation, Inspection and

Maintenance; and the employer shall ensure that lift inspectors are
qualified and that they are adequately trained in the inspection of the lift.

Shall establish procedures to periodically maintain the lift in accordance
with the lift manufacturer’s instructions or ANSI/ALI ALOIM, Standard for
Automotive Lifts

– Safety Requirements for Operation, Inspection and

Maintenance; and the employer shall ensure that lift maintenance
personnel are qualified and that they are adequately trained in the
maintenance of the lift.

Shall maintain the periodic inspection and maintenance records
recommended by the manufacturer or ANSI/ALI ALOIM, Standard for
Automotive Lifts

– Safety Requirements for Operation, Inspection and

Maintenance.

Shall display the lift manufacturer’s operating instructions; ALI/SM,
“Lifting It Right” safety manual; ALI/ST, “Safety Tips” card; ANSI/ALI
ALOIM, Standard for Automotive Lifts

– Safety Requirements for

Operation, Inspection and Maintenance; ALI/WL Series, ALI Uniform
Warning Label
Decals/Placards; and in the case of frame engaging lifts, ALI/LP-Guide,
“Quick Reference Guide – Vehicle Lifting Points for Frame Engaging
Lifts”; in a conspicuous location in the lift area convenient to the operator.

Shall review and understand the proper requirements outlined in
ANSI/ALI ALIS, Safety Requirements for Installation and Service of
Automotive Lifts.

«
...
15
16
17
18
19
...
»

Summary of Contents for V-035-A-X

















































































































Reviews:

No comments

Related manuals for V-035-A-X

Q-SYS Core 110f

Brand: QSC Pages: 2

Brand: MAC TOOLS Pages: 20

Brand: Gude Pages: 122

Xenta 400 Series

Brand: TAC Pages: 48

Brand: EC POWER Pages: 62

Brand: Northern Industrial Tools Pages: 18

Brand: ATH Pages: 76

Brand: Fenix Pages: 24

Brand: National Instruments Pages: 9

Auto-Cut 200 XT

Brand: Victor Pages: 166

Brand: Ravaglioli Pages: 86

Brand: Spartus Pages: 28

Brand: TECNA Pages: 44

CondorLift CSmag 100

Brand: Carl Stahl Kromer Pages: 56

Brand: morse Pages: 6

Brand: Vicon Pages: 91

Brand: AMW Pages: 44

Brand: AMH Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands