manualshive.com logo in svg

MKS Mass-Flo 1159B, Manual, Page: 25 / 57

Share
Download
MKS Mass-Flo 1159B Manual Download Page 25

Chapter Two:  Installation

Gas Line Connections

15

Gas Line Connections

The 1100 Series is equipped with ¼ inch Swagelok

®

 fittings.  Cajon

®

  4-VCR

®

  (male)

compatible, and Cajon

®

  4-VCO

®

 (male) compatible fittings are available as options.  Refer to

the manufacturers’ specifications for installation information on VCR and VCO compatible
fittings.

How To Install a Swagelok Fitting

To connect the ¼ inch Swagelok fittings, follow the steps below.

1. Be sure the tubing is clean and free of axial scratches.

2. Insert the tubing through the compression nut and ferrules all the way to the shoulder.

Figure 5 shows the components in a standard compression fitting.

Nut

Back Ferrule

Shoulder

Body

Front Ferrule

Figure 5:  Standard Compression Fitting

Caution

Tighten the nut only 1¼ turns past finger-tight.  When remaking,
tighten the nut only 

1

/

6

 turn.  Overtightening damages the tubing and

fitting, and destroys a normally leak-tight fitting.

3. Connect the fitting on the other side of the MFC (one fitting is for gas input and the other

fitting is for gas output).

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Mass-Flo 1159B


























































Reviews:

No comments