manualshive.com logo in svg

MKS Baratron 127A, Instruction Manual, Page: 5 / 38

Share
Download
MKS Baratron 127A Instruction Manual Download Page 5

Table of Contents

iii

Table of Contents

Pressure Transducer Safety Information.................................................................................. 1

Symbols Used in This Instruction Manual.................................................................. 1

Symbols Found on the Unit ....................................................................................... 2

Safety Procedures and Precautions ............................................................................. 3

Chapter One:  General Information......................................................................................... 5

Introduction ............................................................................................................... 5

How This Manual is Organized.................................................................................. 6

Customer Support ...................................................................................................... 7

Chapter Two:  Installation ...................................................................................................... 9

How To Unpack the Type 127/128 Unit..................................................................... 9

Unpacking Checklist ..................................................................................... 9

Interface Cables ......................................................................................................... 10

Generic Shielded Cable Description .............................................................. 11

Example 1:  Preferred Method To Connect Cable .......................................... 12

Example 2:  Alternate Method To Connect Cable .......................................... 12

Product Location and Requirements........................................................................... 13

Operating Environmental Requirements ........................................................ 13

Setup ......................................................................................................................... 13

Dimensions ................................................................................................... 14

Electrical Information ................................................................................................ 15

Connector...................................................................................................... 16

Chapter Three:  Overview....................................................................................................... 17

Circuit Description..................................................................................................... 17

Labels........................................................................................................................ 18

Chapter Four:  Operation........................................................................................................ 19

How To Zero the Type 127/128 Transducer ............................................................... 19

Chapter Five:  Maintenance.................................................................................................... 21

General Information................................................................................................... 21

Summary of Contents for Baratron 127A







































Reviews:

No comments