manualshive.com logo in svg

MKS Baratron 127A, Instruction Manual, Page: 17 / 38

Share
Download
MKS Baratron 127A Instruction Manual Download Page 17

Chapter Two:  Installation

How To Unpack the Type 127/128 Unit

9

Chapter Two:  Installation

How To Unpack the Type 127/128 Unit

MKS has carefully packed the Type 127/128 unit so that it will reach you in perfect operating
order.  Upon receiving the unit, however, you should check for defects, cracks, broken
connectors, etc., to be certain that damage has not occurred during shipment.

Note

Do not discard any packing materials until you have completed your
inspection and are sure the unit arrived safely.

If you find any damage, notify your carrier and MKS immediately.  If it is necessary to return the
unit to MKS, obtain an ERA Number (Equipment Return Authorization Number) from the MKS
Service Center before shipping.  Please refer to the inside of the back cover of this manual for a
list of MKS Calibration and Service Centers.

Unpacking Checklist

Standard Equipment:

•

Type 127 or Type 128 Unit

•

Type 127/128 Instruction Manual (this book)

Optional Equipment:

•

Electrical Connector Accessories Kit - 127A-K1 or 128A-K1 (which includes a mating
connector for the 15-pin Type “D” Interface connector)

•

Interface cables

•

PDR-C-1C/2C Power Supply/Readout

•

RM-6 Rack Mount Kit

•

Pressure/Flow Controller

Summary of Contents for Baratron 127A







































Reviews:

No comments