Mitsubishi QCPU Structured Programming Manual Download Page 5

Page: 5 / 242

A-3

INTRODUCTION

Thank you for purchasing the Mitsubishi MELSEC-Q series programmable controller.

Before using the product, thoroughly read this manual to develop full familiarity with the programming

specifications to ensure correct use.

Please forward this manual to the end user.

CONTENTS

SAFETY PRECAUTIONS ................................................................................................................................ A - 1

REVISIONS....................................................................................................................................................... A - 2

INTRODUCTION............................................................................................................................................... A - 3

CONTENTS ...................................................................................................................................................... A - 3

MANUALS......................................................................................................................................................... A - 6

PURPOSE OF THIS MANUAL ......................................................................................................................... A - 9

GENERIC TERMS AND ABBREVIATIONS IN THIS MANUAL...................................................................... A - 11

1.2 Modules and Versions Applicable to Instructions

1 - 3

2. INSTRUCTION TABLES

2 - 1 to 2 - 10

2.1 How to Read Instruction Tables

2 - 2

2.2 QCPU Instruction Tables

2 - 3

2.2.1 Analog instruction .......................................................................................................................... 2 - 3

2.2.2 Serial communication and modem interface instruction ................................................................ 2 - 4

2.2.3 CC-Link instruction ........................................................................................................................ 2 - 5

2.2.4 CC-Link IE controller network, MELSECNET/H, and Ethernet instruction .................................... 2 - 6

2.2.5 PID control instruction (inexact differential) ................................................................................... 2 - 8

2.2.6 PID control instruction (exact differential) ...................................................................................... 2 - 9

2.2.7 Positioning instruction.................................................................................................................... 2 - 9

3. CONFIGURATION OF INSTRUCTIONS AND DATA SPECIFICATION

3 - 1 to 3 - 4

3.1 Configuration of Instructions and Data Specification Methods

3 - 2

4. HOW TO READ INSTRUCTIONS

4 - 1 to 4 - 6

5. QCPU INSTRUCTION DETAILS

5 - 1 to 5 - 196

5.1 Analog Instruction

5 - 2

5.1.1 OFFGAN instruction ...................................................................................................................... 5 - 2

5.1.2 OGLOAD instruction ...................................................................................................................... 5 - 3

5.1.3 OGSTOR instruction.................................................................................................................... 5 - 27

5.2 Serial Communication and Modem Interface Instruction

5 - 51

5.2.1 ONDEMAND instruction .............................................................................................................. 5 - 51

5.2.2 OUTPUT instruction..................................................................................................................... 5 - 53

5.2.3 INPUT instruction......................................................................................................................... 5 - 55

5.2.4 BIDOUT instruction...................................................................................................................... 5 - 57

Summary of Contents for QCPU



















































































































































































































































Search results

Summary of Contents for QCPU

Reviews:

Related manuals for QCPU

Brands by name

Popular brands

Mitsubishi QCPU, Structured Programming Manual

Search results

Summary of Contents for QCPU

Reviews:

Related manuals for QCPU

Brands by name

Popular brands