Mitsubishi QCPU Structured Programming Manual Download Page 172

Page: 172 / 242

5-134

5.4 CC-Link IE Controller Network, MELSECNET/H, and Ethernet Instruction
5.4.14 REMFR instruction

Z_REMFR

5.4.14

REMFR instruction

Z_REMFR

*1: Local devices and file registers per program cannot be used as setting data.

Z(P)_REMFR

P: Executing condition

indicates any of the following

instructions.

Z_REMFR

ZP_REMFR

Input argument

EN:

Executing condition

:Bit

Jn*:

Network number of the host station

:String

n1:

Channel number

:ANY16

n2:

Target station number

:ANY16

n3:

Start I/O number of the target intelligent function module
Specifies the higher three digits when expressing the I/O
number for the intelligent function module mounted to the
target remote I/O station in four digits.

:ANY16

n4:

Read buffer memory start address
Specifies the start address of the buffer memory for the read
destination intelligent function module.

:ANY16

n5:

Number of read points (in units of words)

:ANY16

Output argument

ENO:

Execution result

:Bit

d1:

Start number of the device that stores read data (host station)
Specifies the start number of the host station's device that
stores read data.

:ANY16

d2:

Variable that turns ON upon completion of the instruction
d2[1] also turns ON at the time of error completion.

:Array of bit [0..1]

Setting

data

Internal device

R, ZR

Constant

K, H

Others

Bit

Word

Bit

Word

−

Structured ladder

ENO

Z_RE

(EN, J

, d1, d2);

ENO:=

Summary of Contents for QCPU



















































































































































































































































Search results

Summary of Contents for QCPU

Reviews:

Related manuals for QCPU

Brands by name

Popular brands

Mitsubishi QCPU, Structured Programming Manual

Search results

Summary of Contents for QCPU

Reviews:

Related manuals for QCPU

Brands by name

Popular brands