Mitsubishi QCPU Structured Programming Manual Download Page 184

Page: 184 / 242

5-146

5.4 CC-Link IE Controller Network, MELSECNET/H, and Ethernet Instruction
5.4.20 BUFSND instruction

ZP_BUFSND

ont

l Da

(1) Send data

Device

Item

Setting data

Setting range

Setting side

[0]

System area

–

[1]

Completion status

The instruction completion status is stored.

: Normal completion

Other than 0

: Error completion (error code)

–

System

Device

Item

Setting data

Setting range

Setting side

Send data length

Data length of the data read from the fixed buffer data area is stored.
(Data length becomes the number of words or the number of bytes
depending on the procedure used in fixed buffer communication.)

–

User

With procedure (communication in binary code): The number of
words

1 to 1017

With procedure (communication in ASCII code): The number of
words

1 to 508

Nonprocedural communication (communication in binary code):
The number of bytes

1 to 2046

Send data

Specify the send data.

–

User

Summary of Contents for QCPU



















































































































































































































































Search results

Summary of Contents for QCPU

Reviews:

Related manuals for QCPU

Brands by name

Popular brands

Mitsubishi QCPU, Structured Programming Manual

Search results

Summary of Contents for QCPU

Reviews:

Related manuals for QCPU

Brands by name

Popular brands