manualshive.com logo in svg

Mitsubishi QCPU, Structured Programming Manual

The Mitsubishi QCPU Structured Programming Manual is an essential resource for users of this advanced automation product. With step-by-step instructions, it guides you through the programming process, ensuring seamless operation. Download this comprehensive manual for free from manualshive.com and unlock the full potential of Mitsubishi QCPU.

Share
Download
background image

5.4 CC-Link IE Controller Network, MELSECNET/H, and Ethernet Instruction

5.4.2 SREAD instruction

5-101

5

QCP

U

 IN

S

T

RUCTI

O

N 

DE

TA

IL

S

J_

SREAD,

 G

_

SRE

AD

J_SREAD, G_SREAD

Function

This instruction reads data from a word device of another station.

C

ont

r

o

l Da

t

a

For the control data of the SREAD instruction that reads the word device memory of another 
station, refer to READ instruction.

The control data of the SREAD instruction are the same as those of the READ instruction.

Accordingly, this section omits the explanation.

Summary of Contents for QCPU



















































































































































































































































Reviews:

No comments

Related manuals for QCPU

Particle B Series Quick Start Manual preview
B Series
Brand: Particle Pages: 6
K&K M15 Manual preview
M15
Brand: K&K Pages: 6
Quectel BG96 At Command Manual preview
BG96
Brand: Quectel Pages: 23
Quectel BG96 Hardware Design preview
BG96
Brand: Quectel Pages: 79
Cansec H1000 Installation Manual And Instructions For Use preview
H1000
Brand: Cansec Pages: 45
Cansec CP40 Installation Manual preview
CP40
Brand: Cansec Pages: 43
Cansec MAP2 Installation Manual preview
MAP2
Brand: Cansec Pages: 32
Samson 3351 Mounting And Operating Instructions preview
3351
Brand: Samson Pages: 20
YASKAWA FSDrive-MV1000 Series Instructions For Use Manual preview
FSDrive-MV1000 Series
Brand: YASKAWA Pages: 260
YASKAWA iQpump1000 Installation & Start?Up Manual preview
iQpump1000
Brand: YASKAWA Pages: 114
YASKAWA MOTOMAN FS100 Operator'S Manual preview
MOTOMAN FS100
Brand: YASKAWA Pages: 20
YASKAWA yasnac lx3 Maintenance Manual preview
yasnac lx3
Brand: YASKAWA Pages: 152
YASKAWA GPD 506/P5 Technical Manual preview
GPD 506/P5
Brand: YASKAWA Pages: 66
YASKAWA MOTOMAN FS100 Option Addendum preview
MOTOMAN FS100
Brand: YASKAWA Pages: 20
YASKAWA MOTOMAN FS100 Instructions Manual preview
MOTOMAN FS100
Brand: YASKAWA Pages: 17
YASKAWA 1000-Series Technical Manual preview
1000-Series
Brand: YASKAWA Pages: 58
YASKAWA J1000 CIMR-JC series Cheat Sheet preview
J1000 CIMR-JC series
Brand: YASKAWA Pages: 2
YASKAWA SI-EP3 Technical Manual preview
SI-EP3
Brand: YASKAWA Pages: 58

Brands by name

Popular brands

Load more brands