manualshive.com logo in svg

Mitsubishi Heavy Industries SRRM25ZF-S, Technical Manual, Page: 45 / 127

Share
Download
Mitsubishi Heavy Industries SRRM25ZF-S Technical Manual Download Page 45

-

 43 

-

LO

MED

HI

AUTO

HI POWER

ECONO

ON

OFF

AM

PM

FAN SPEED button

Each time the button is pushed, the

 indi-

cator is switched over in turn.

•

The above illustration shows all controls, but in practice
only the relevant parts are shown.

OPERATION MODE select button

Each time the button is pushed, the

 indi-

cator is switched over in turn.

AIR FLOW button

This button changes the flap mode. When
pressed, this button changes the mode in the
following order:

ON/OFF button

Press for starting operation, press again for
stopping.

HI POWER button

This button changes the HIGH POWER
mode.

ECONO button

This button changes the ECONOMY mode.

RESET switch

Switch for resetting microcomputer.

ON TIMER button

This button selects ON TIMER operation.

TIME switch

This switch for setting the clock.

OFF TIMER button

This button selects OFF TIMER operation.

TEMPERATURE button

This button sets the room temperature.
(This button changes the present time and
TIMER time.)

CANCEL button

This button cancels the ON timer and OFF
timer.

RESERVE button

This button sets the present time and
TIMER time.

S

 Indication section

OPERATION MODE indicator

Indicates selected operation with

 lamp.

[ 

(Auto) • 

(Cool) • 

(Heat) • 

(Dry)]

TEMPERATURE indicator

Indicates set temperature.
(Does not indicate temperature when operation
mode is on AUTO)

FAN SPEED indicator

Indicates set air flow rate with

 lamp.

AIR FLOW indicator

Shows selected flap mode.

HI POWER MODE indicator

Indicates during Hi POWER mode operation.

ECONO MODE indicator

Indicates during ECONOMY mode operation.

ON TIMER indicator

Indicates during ON TIMER operation.

TIME indicator

Indicates present time or timer setting time.

OFF TIMER indicator

Indicates during OFF TIMER operation.

(1)

Wireless remote control

Models All models

S

 Operation section

(Air scroll)

(Swing)

4

OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER

4.1 Operation control function by remote control switch

This button is not used for SRRM-ZF series.
(Air flow direction adjustment can not be
performed.)

(Flap stopped)

Summary of Contents for SRRM25ZF-S
































































































































Reviews:

No comments