background image

-

 78 

-

 '15 • PAC-T-236

— 4 —

2 . Accessories & prepare on site

Item name

Q’ty

Remark

Switch box

For 1 piece or 2 pieces (JIS C 8340 or 

equivalent)

1

These are not required when installing 

directly on a wall.

Thin wall steel pipe for electric appliance

(JIS C 8305 or equivalent)

As required

Lock nut, bushing (JIS C 8330 or equivalent) As required

Lacing (JIS C 8425 or equivalent)

As required Necessary to run R/C cable on the wall.

Putty

Suitably For sealing gaps

Molly anchor

As required

R/C cable (0.3 mm

2

 x 2 pcs)

As required See right table when longer than 100 m

Accessories

R/C main unit, wood screw (ø3.5 x 16) 2 pcs
User’s Manual, Installation Manual

Parts procured at site

When the cable length is longer than
100 m, the max size for wires used
in the R/C case is 0.5 mm

2

. Connect

them to wires of larger size near
the outside of R/C. When wires are
connected, take measures to prevent
water, etc. from entering inside.

< 200 m

0.5 mm

2

 x 2-core

< 300 m

0.75 mm

2

 x 2-core

< 400 m

1.25 mm

2

 x 2-core

< 600 m

2.0 mm

2

 x 2-core

3. Remote control installation procedure

Determine where to install the remote control

Installation

“Using a switch box”
“Installed directly on a wall”

Wiring direction “Backward”

“Upper center”, “Upper left”

Cautions for selecting installation place

(1) Installation surface must be flat and sufficiently strong.

R/C case must not be deformed.

(2) Where the R/C can detect room temperatures accurately.

This is a must when detecting room temperatures with
the temperature sensor of R/C.

 · Install the R/C where it can detect the average tempera-

ture in the room.

 · Install the R/C separated from a heat source sufficiently.
 · Install the R/C where it will not be influenced by the

turbulence of air when the door is opened or closed.

Select a place where the R/C is not exposed to direct
sunlight or blown by winds from the air-conditioner or
temperatures on the wall surface will not deviate largely
from actual room temperature.

Installation space

30mm

30mm

30mm

120mm

R/C temperature sensor

Wiring

Secure minimum spaces for 
disassembling the case.
Upper left and Upper right sides

……30mm or more

Bottom side…120mm or more

If using L-shaped 

screwdriver, 50mm or 
more is available.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Summary of Contents for RC-EX1A















Reviews: