Mitsubishi Electric PUMY-P112VKM5-ERBS Technical & Service Manual Download Page 138

Page: 138 / 140

OPERATING PROCEDURE

PHOTOS/FIGURES

13. Removing the compressor (MC)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove 2 front cover panel fixing screws (5 × 12) and

remove the front cover panel. (See Photo 4)

(4) Remove front panel fixing screws, 5 (5 × 12) and 2 (4 ×

10) and remove the front panel. (See Photo 4)

(5) Remove 4 back cover panel fixing screws (5 × 12) and

remove the back cover panel.

(6) Remove the electrical parts box. (See Photo 5)

(7) Remove 3 valve bed fixing screws (4 × 10) and 4 ball valve

and stop valve fixing screws (5 × 16) and then remove the

valve bed. (See Photo 4 and 7)

(8) Remove 3 right side panel fixing screws (5 × 12) in the

rear of the unit and then remove the right side panel.

(9) Remove 3 separator fixing screws (4 × 10) and remove

the separator. (See Figure 1)

(10) Recover refrigerant.

(11) Remove the 3 compressor fixing nuts for motor using

spanner or adjustable wrench.

(12) Remove the welded pipe of motor for compressor inlet

and outlet and then remove the compressor.

Note:

Recover refrigerant without spreading it in the air.

Photo 13

Figure 1

14. Removing the accumulator

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove 2 front cover panel fixing screws (5 × 12) and remove the front cover panel. (See Photo 4)

(4) Remove 4 back cover panel fixing screws (5 × 12) and remove the back cover panel.

(5) Remove the electrical parts box. (See Photo 5)

(6) Remove 3 valve bed fixing screws (4 × 10) and 4 ball valve and stop valve fixing screws (5 ×16), and then remove the valve

bed. (See Photo 4 and 7)

(7) Remove 3 right side panel fixing screw (5 × 12) in the rear of the unit and then remove the right side panel.

(8) Recover refrigerant.

(9) Remove 4 welded pipes of accumulator inlet and outlet.

(10) Remove 2 accumulator leg fixing screws (4 × 10). (See Photo 15)

Note:

Recover refrigerant without spreading it in the air.

Photo 14

Photo 15

Accumulator

Accumulator leg

Accumulator leg fixing

screws

Separator

fixing

screws

Separator

fixing screw

Accumulator

Inlet

Outlet

Compressor

(MC)

Valve bed

fixing screw

Valve

bed fixing

screws

Compressor

fixing nuts

Separator

Accumulator

138

OCH740

Summary of Contents for PUMY-P112VKM5-ERBS













































































































































Search results

Summary of Contents for PUMY-P112VKM5-ERBS

Reviews:

Related manuals for PUMY-P112VKM5-ERBS

Brands by name

Popular brands

Mitsubishi Electric PUMY-P112VKM5-ERBS, Technical & Service Manual

Search results

Summary of Contents for PUMY-P112VKM5-ERBS

Reviews:

Related manuals for PUMY-P112VKM5-ERBS

Brands by name

Popular brands