Mitsubishi Electric PUMY-P112VKM5-ERBS Technical & Service Manual Download Page 84

Page: 84 / 140

Check code

6607

(A7)

No ACK error

Chart 1 of 4

Abnormal points and detection methods

Causes and checkpoints

1. Represents a common error detection

An abnormality detected by the sending side controller when receiving

no ACK from the receiving side, though signal was once sent. The

sending side searches the error in 30 seconds interval for 6 times

continuously.

1. The previous address unit does not exist since

the address switch was changed while in electric

continuity status.

2. Decline of transmission voltage/signal caused by

tolerance over on transmission line

·At the furthest end: 200 m
·On remote controller line: (12 m)

3. Decline of transmission voltage/signal due to

unmatched transmission line types

·Types for shield line: CVVS, CPEVS, or MVVS
·Line diameter: 1.25

or more

4. Decline of transmission voltage/signal due to

excessive number of connected units

5. Malfunction due to accidental disturbance such as

noise or lighting surge

6. Defect of error source controller

2. The cause of displayed address and attribute is on the outdoor unit side

An abnormality detected by the indoor unit if receiving no ACK when

transmitting signal from the indoor unit to the outdoor unit.

1. Contact failure of indoor/outdoor unit transmission

line.

2. Disconnection of transmission connector (CN2M) on

indoor unit.

3. Malfunction of sending/receiving circuit on indoor/

outdoor unit.

4. Disconnection of the connectors on the circuit board

3. The cause of displayed address and attribute is on the indoor unit side

An abnormality detected by the remote controller if receiving no ACK

when sending data from the remote controller to the indoor unit.

1. While operating with multi refrigerant system indoor

units, an abnormality is detected when the indoor

unit transmit signal to the remote controller during

the other refrigerant-system outdoor unit is turned

OFF, or within 2 minutes after it turned back ON.

2. Contact failure of indoor unit or remote controller

transmission line

3. Disconnection of transmission connector (CN2M) on

indoor unit

4. Malfunction of sending/receiving circuit on indoor

unit or remote controller

4. The cause of the displayed address and attribute is on the remote

controller side

An abnormality detected by the indoor unit if receiving no ACK when

transmitting signal from the indoor unit to the remote controller.

1. While operating with multi refrigerant system indoor

units, an abnormality is detected when the indoor

unit transmit signal to the remote controller during

the other refrigerant-system outdoor unit is turned

OFF, or within 2 minutes after it turned back ON.

2. Contact failure of indoor unit or remote controller

transmission line

3. Disconnection of transmission connector (CN2M) on

indoor unit

4. Malfunction of sending/receiving circuit on indoor

unit or remote controller

OCH740

Summary of Contents for PUMY-P112VKM5-ERBS













































































































































Search results

Summary of Contents for PUMY-P112VKM5-ERBS

Reviews:

Related manuals for PUMY-P112VKM5-ERBS

Brands by name

Popular brands

Mitsubishi Electric PUMY-P112VKM5-ERBS, Technical & Service Manual

Search results

Summary of Contents for PUMY-P112VKM5-ERBS

Reviews:

Related manuals for PUMY-P112VKM5-ERBS

Brands by name

Popular brands