Mitsubishi Electric PRH-P10MYA Technical & Service Manual Download Page 44

Page: 44 / 87

[2] Control specifications

(1) Protection functions

1) The main protection devices for the unit are:

a) High pressure protection (63H1)

b) Compressor overcurrent protection (51C)

c) Liquid temp thermistor trouble (TH1)

d) Discharge temperature protection (TH2

≥

118

e) Discharge temp thermistor trouble (TH2)

Condenser/evaporater temp thermistor trouble (TH3)

g) Low

h) Inlet temp thermistor trouble (TH4)

Liquid temp thermistor trouble (TH5)

Condenser/evaporater temp thermistor trouble (TH6)

pressure protection (63L)

2) When tripping of a detection device is sensed, the check mode is entered and the compressor is stopped. (After 3

minutes, the compressor restarts.) Thereafter, the compressor is stopped when the specified number of check

modes or greater is sensed within the check time.

3) Check mode is released by stopping operation, changing the operation mode, or check mode time up. A check

mode is also released by stopping of operation by remote controller.

4) Detected check mode history (newest) and abnormality history (last 2 times) are memorized and are displayed on

the segment by circuit board DIP switch setting.

The operation mode when the newest abnormality was generated, the thermistor temperature (TH1,2,3), and the

thermostat ON time can also be displayed.

Protection functions

a) High pressure protection

(63H1)

b) Compressor overcurrent

protection (51C)

c) Liquid temp thermistor

trouble (TH1)

d) Discharge temperature

protection (TH2

118

e) Discharge temp ther-

mistor trouble (TH2)

f) Condenser/evaporater

temp thermistor trouble

(TH3)

g) Low pressure protection

(63L)

Operation value

3.3 MPa

P8MYA: 22 A

P10MYA: 27 A

Less than –39

C or

greater than 88

Less than –40

C or

greater than 90

Less than –40

C or

greater than 90

Less than –40

C or

greater than 90

Greater than 118

Less than 0

C or

greater than 216

Less than –39

C or

greater than 88

0 MPa

Detection condition

Compressor operating

Compressor operating except for

10 minutes at end of defrosting

and 7 minutes while compressor

starting

Compressor operating

Compressor operating except for

10 minutes at end of defrosting

and 5 minutes while compressor

starting

Compressor operating except for

10 minutes at end of defrosting

and 7 minutes while compressor

starting

Compressor operating except for

defrosting, 10 minutes at end of

defrosting

Number of

check modes

1 time

2 times

4 times

Check time

–

30 minutes

h) Inlet temp thermistor

trouble (TH4)

Cooling, heating operating

1 time

3 minutes

i) Liquid temp thermistor

trouble (TH5)

Cooling, heating operating

1 time

3 minutes

j) Condenser/evaporater

temp thermistor
trouble (TH6)

Cooling, heating operating

1 time

3 minutes

- 41 -

Summary of Contents for PRH-P10MYA
























































































Search results

Summary of Contents for PRH-P10MYA

Reviews:

Related manuals for PRH-P10MYA

Brands by name

Popular brands

Mitsubishi Electric PRH-P10MYA, Technical & Service Manual

Search results

Summary of Contents for PRH-P10MYA

Reviews:

Related manuals for PRH-P10MYA

Brands by name

Popular brands